I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
Dear friends,
My 52840 DK flashed a serial example( nrf5_SDK_for_Mesh_v5.0.0_src\examples\serial ) as a provisioner.
We use PyACI communicate with provisioner by Uart...
Good evening,
Referring to the following page which lists IDEs that are supported by Nordic Nordic Supported IDEs
Please kindly let me know if the following toolchain...
Hello,
first I have to say that I'm new with nRF5340, Segger Embedded Studio and Cmake.
I have a working project with CMakeList.txt. So I include it into Segger Embedded...
Hi.
I am trying communication from nRF52832 to iPhone using ble.
I use main function which put in nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_uart.
But,I...
Hello,
I have done the setup of Lsm5dsl with Nrf52832 DK board but I little bit confused about what hardware configuration is there so please guide me.
This is Code...
Hello Nordic great team,
We have a question please, we would like to configure our IOT device through the air, and the best way as we see in our use case, is to use the...
Hi there,
I tried to configure the openthread co-processor radio.
The build went well for my nRF52840 dongle, I managed to generate the RCP package image but when I install...
Hi!
I'm working with the nRF52833 in a Laird dev kit, the bl653_dvk and I cannot build a Hello World with mcuboot application in nrf sdk 1.7.0 or greater.
Although in...
Added the below lines to the peripheral_hr and I could see the logs without any trouble.
Same lines added to the central_and_peripheral_hr and I can see anything. What I...
Does someone have experience driving several slaves on a QSPI bus? Can we use a general IO pin for Chip Select (CS)? [Edtit] (I believe the nCS - QSPI pin described in the...
Hi,
I am trying to filter an iBeacon sample using a modified version of the central_hr_code.
Changes on the central_hr_code:
Added 128-bit UUID definition:
Added...
Hi,
I am developing a health wearable and want to store biosignal data into flash and then read at some point. I found that the reading process is relative slow as I tested...
Hi,ALL:
I use esb 2.4G liberary,and I found the same kind of produc build of nrf52840,it's radio current consumption is 1.2mA-1.3mA,how can it do it? My project is build...
Hi,
I have 2 nrf52840 DK boards advertising on coded PHY mode. Once connected the connection is updated (using sd_ble_gap_phy_update()) to use 2M mode. No problem in doing...
