I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
Hi All.
Following the step by step guide on Getting started with Nordic's secure DFU bootloader, when I try to build the uECC library by issuing a make command, I systematically...
We currently have an older Sena SD1000 bluetooth module in an embedded system that functions as a UART wireline replacement. We just connect it to a UART on the embedded controller...
Hi, I have a simple application with logic is: - every 3 or 20 seconds send some data via modem (based on AT commands), - sending and receiving data via serial port to and...
Hello,
I am attempting to find gerber data for the development PC or a mechanical drawing of connector locations. I would like to make a PCB that plugs into this board...
Hi, guys! I noticed this answer from the devzone .
I have nRF52 DK and an nRF Thingy. I want to play a short speech using I2S with MAX98357A .
This speech is usually...
Hey,
simple question: What is the recommend approach on prolonging the advertising period?
Example:
User clicks a button -> advertising starts for 180 seconds.
User...
Hi Support,
I am testing current consumption of NRF_TIMER1, below is my code snippets, basically, I just start timer1 task and then stop it.
After the two code lines...
Hi there, I really much in trouble with USB CDC ACM. So that would be great if you can help me out with this: I upload the "USB CDC ACM" example (SDK verison 15.2) to my nRF52840...
This is a question of curiosity rather than a specific concern: In my sdk_config.h I have my prescaller set to 0: Based on this, the RTC1 used for AppTimer should rollover...
I am working on an older project that was developed using SDK 11.0.0, SD S132 2.0.1, and "Eclipse 2018-9." No MDK appears to be being used.
I understand that the MDKs are...
Hello,
BLE 5 applications on the nRF52810 which softdevice should we be using S112 / S132 what are the primary differences between these? I wanted to know a comparison...
Hi,
I'm collecting data from BLE and storing them into nRF52840 Dongle by using nrf_fstorage_write procedure. Everything works fine so I can write data into flash by nrf_fstorage_write...
When I run the TWI scanner example, an unknown address shows up in tandem with my TWI device address.
I am connecting a MAX30101 EV kit daughter board to the nRF52840...
In the secure DFU bootloader, I have some custom initialization that I need to happen after the BLE transport is initialized in nrf_dfu_init(), but before loop_forever() in...
