Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hi everyone,
I have a nrf52-DK, I made samples with the saadc unit and i noticed there are unexplained peaks.
I connected the MIC's output (its VDD is from the board)...
Hi I bought quite a few of these on boards on e-bay and have worked a lot with them.
One thing that is confusing me is the variation in the number of retries, even when...
Hi,
I have tested a sample code which sends some data through BLE in nRF52 development kit(PCA10400). The code is attached below.
nRF5_SDK_11.0.0_MPU6050_Acc_X_Output...
I'm trying to compile the bootloader_secure example for the 10040 dev board using make, and it appears the makefile was not updated correctly with the changes made to the...
Segger RTT viewer is a great debugging tool. But every time when I download new firmware into my board I have to close the viewer and then open it after download is finished...
Hi guys,
in my application, I'm trying to do multiple fota, I succeed at the first time & after that I can jump again to the bootloader, but after that something is going...
I used nRF51822 IC and SDK11 with softdevice S130. I found a problem that our product cannot work. I dumped the hex code of 2sets from 0x00000000 to 0x0003ffff. One can work...
Hi,
I am using the nRF51822 module. I am facing problem to send multiple data formats packets over nrf module. I am using nrf SDK 11 version.
I am attaching my code with...
I want to start developing a Bluetooth device with the NRF52 DK. For debugging and sniffing purposes to see what is going over the air, use the NRF51 dongle, get a NRF51 DK...
In the nRF52 specification, I cannot find figures for the interrupt latency for event on GPIO pins in different power mode OFF, ON (constant latency, Low Power).
Can you...
Hi. I need to use direct advertising option in my application to minimize the time needed to establish the connection.
Firstly, I set up the connection during "normal" fast...
Dear Nordic Team,
Thanks for supporting.
I am try to work multiple (Peripheral) tag ID read with one central and stored in my PC via UART communication. Which example...
Hi,
I am new to nRF microcontroller and communication . currently, I am working on nRF51822 microcontroller. I am able to communicate between two nRF51822 microcontrollers...
I am trying to modify make file of UART with make file of timer to give the functionality of UART and timer. I created the single code in main c file and added necessary source...
