I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
Dear all:
My device uses LDO mode and DC-DC mode respectively, and the distance is different.In 4dbm, the distance of the LDO mode is 110m, while the LDO mode is in the 70m...
Hi,
I was wondering if anyone could clarify why there are enable, set and clear (CHEN, CHENSET, CHENCLR) for the PPI channels when according to the data sheet they all...
I checked S130 document for using nRF51822.
I want to change the nRF51822 like the following mode.
peripheral => central => scanning => peripheral => central => scanning...
Hello
I am trying to change the ticks value of Battery measurement interval (ble_app-prox example) but i am not able to understand how the ticks period is measured based...
Hi,
I was seeing memory leak issues when using NRF51 with JLkink v4.98. See this link:
forum.segger.com/index.php
This issue has been fixed with the latest version of...
The address miss event is not shown as a transition in Figure 22 of the NRF51 Reference Manual. What state does the NRF51 enter upon an address miss and how long after the...
To use BEL application, the soft device must be downloaded before programming.
i can find a table shows that which soft device version is suitable for chip version.
how...
Our application is developing RC units for small (indoor) model airplanes - we want to be able to have multiple planes flying at once without "stepping" on each other.
...
I'm developing a NUS-based peripheral and adding a timeout to force a disconnect after a period of inactivity (i.e. no incoming NUS data). However my peripheral also provides...
Hi all,
I'm trying to use Ant+ HRM RX demo profile from nRF51_SDK_10 ( nRF51422 ) between my board PCA10028 and a Garmin rate sensor but I get some trouble.
Let me explain...
In the example iOS app and the DFU service in the firmware there is a DFU revision characteristic UUID 0x1534. The Nordic SDK documentation don't mention this characteristic...
HI，I'm having trouble in flash operation.I I did an experiment of flash operation.I call pstorage_store( ) or pstorage_load( ) very second after nrf51822 connected with app...
I would like to know how long TXIDLE state takes, between sending two data packets, for NRF51822? I want to minimize the time between sending two data packets, to maximize...
Hi,
Everyone,
I am trying to understand BLE app code and using debugger to find the values of the data sent over BLE during advertising mode.
But during debugging I...
