I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Hello, I have a problem with my own designed board, It has nRF52832 and some other sensors which communicate over SPI, also I have a SD card on the same bus that works fine...
Hello,
In my code I am reading from a sensor and want to check if the float value returned is out of range. In order to do so I would like to be able to calculate the absolute...
i have just blinked the LED and trying to pwm
i have written a simple led blinking program like this one below
#include <stdbool.h> #include <stdint.h> #include "nrf_delay...
I'm trying to diagnose frequent (80%) DFU failures that I'm seeing with our Android application using Buttonless mode.
Our target can be 100% reliably updated with our app...
Hello,
I would like to program the NRF52840DK to send ZigBee beacon(not beacon request) to the end devices, but I cannot seem to find the API, etc. to do so.
Or perhaps...
Hello NRF ,
I am not able to run any of the the BLE peripheral example codes from the SDK12.2.0 ( Nordic NRF 52 SDK ) .
The reason I am using 12.2.0 is I have a sensor...
Hi,
I need a battery calculation in my project, For that I need to implement ADC.
But in SDK17 their is no ADC sample example for nrf52810 is present. So please suggest...
Hi Team,
I have nrf52840 DK board and is trying to get the prints from nRF USB port using cdc_acm application. I can see the prints when I connect the DK board with the...
Hello, I am trying to set the company ID and manufacturer specific data in the NCS SDK using nRF52840 dev board
I have the following array of structure
uint8_t COMPANY_ID...
Hi,
I am trying to generate unique key(s) for every device and store them in Optiga to sign the messages, among others. After generating the key pairs, I need the private...
Hello. Currently, the Samsung Galaxy A series has a problem that UART communication is not available.
I want to find the cause and solution of this problem, How can I find...
I am using nrf52852 with sdk 16 version and I want to set the BLE connection interval via BLE command using an customised app. what i want to do is this
#define MIN_CONN_INTERVAL...
HI, I'm developing a device (based on uBlox Anna-B112 with nRF52832) that must securely store three 256bit keys. These keys must remain secret and must not be readable by...
Hi,
I'm just starting out with zephyr on a nrf52dk (nrf52832) and I'm in need of performing some math functions on the data output on a mpu6050.
The MPU6050 is spitting...
We are developing couple of products based on nordic 52810 and 52820. Mainly 52810 And we have received very good support from nordic team and very promp and pro-active support...
