Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hello,
I wanted to implement WDT resets when my application hangs. I am working on the advertiser code, what I observe was when I implement WDT driver in SDK 15.2 examples...
Hi,
I have been working with mesh and I'm using the version 4.2 Mesh SDK.As I understand it I should use nrf_mesh_serial_tx() api to send serial message.When I use this...
Hi There,
I'm working on a datalogger project using nrf52840, includes BLE also. I'm using external 24 channel ADC and should be able to log data to the SDCard at the rate...
Hi, can you explain shortly is it possible to use OTA functionality from FreeRTOS application? I wasn't able to found such an example, and I'm wondering about the possibility...
Most times the Online Power Profiler doesn't even load the graphics, etc. 80% of the time it doesn't finish loading and I have to reload multiple times. I have a 1 Gigabit...
Hello,
I'm using nRF52833 for my application. Unfortunately, my dev kit can not connect to my PC when I use cable to connect it to my PC. It can supply voltage for my kit...
Hi to all, I have found that using SDK17.0.0 on NRF52832, whenever I try to use NRF_LOG_HEXDUMP_DEBUG for a large buffer (more than a 1000 elements), I get a Data Access Violation...
Hello,
I am using NRF52840 DK to toggle led 3 and 4 back and forth (when LED 3 is ON, LED 4 should be OFF and so on). I have to toggle them in a small time interval of...
I get disconnected when receiving notification from characterisitc.
Everything looks fine in nRF Connect app - screenshot below:
Strange behavior begins when I am trying...
hi,
I try to realize all parameter functions in the peer manager. ( I use SDK 15.2.0 )
I expect to design is bond total max 4 in the product. I have some question in below...
Hello,
I'm working on NRF9160-DK. I would like to be able to put the card to sleep in the deepest sleep possible to be able to save as much energy as possible and to wake...
Hi to community again!
I'm having trouble with TWIS during page erase on nRF52840 (FICR "Read 4 bytes @ address 0x10000104 (Data = 0x41414330)") as the bus is stalled...
Hi,
I'm using SDK 17.0.2 on NRF52832
I'm getting an error "undefined reference to `__RAM1_segment_end__'" in "Output/<name>_Debug/Obj/ses_startup_nrf_common.o: in function...
