Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hello. I am now implementing communication to multiple peripheral devices based on the multi-roll project “ble_app_multirole_lesc”. (image1)
Central link after setting memory...
Hello,
I am developing an app for Android using the Android-nRF-Mesh Library, available here: https://github.com/NordicSemiconductor/Android-nRF-Mesh-Library
According...
Hi everyone,
I use nrf52840 DK with Segger embedded studio. I have created a project where I read several sensors data and send these data to mobile through BLE UART.
...
hi,
is it possible to use a j-link programmer like this one in the photo, to program the adafruit nrf52840 board ? is the development procedures will be same as using a...
I am using s132 v5.1.0 and am in the process of implementing an error-handling architecture.
I'm noticing that much of my error handling could be avoided if there were APIs...
I'm trying to get mcuboot to run on the nRF52840 on the nRF9160 board. I have been able to configure it and get the resulting merged.hex file loaded on the processor and it...
Hello ,
I am using a Laird's BL651 module that has a nRF52810 chipset. I have modified the ble_app_uart example to take a command from Rx characteristic and send a response...
I'm working on IEEE 802.15.4 network using nrf52840 DK boards. I'm making use of the examples in 802.15.4 (secure). I wanted to know how the reception between a transmitter...
I am using SDK v15.3 and modifying the ble_app_uart_c example to setup ble_nus connection between nRF DK board and a custom peripheral. I can use nRF Connect to send and receive...
Hello,
I am using nrf52832 with nrf Mesh DK. Is there a way to unprovision the board from the hardware or command line and not from the app?
Many thanks in advance , ...
Hello , I noticed that my NRF DK advertises for a few minutes and goes back to sleep , because of Advertising Timeout set (I am using the BLE Peripheral Example) , but when...
hello,
I am using SDK v15.2.0,s140,pca100056. In my custom application I am using 3 SPI, RTC, timers, USBD, etc.
Actually during the development stage I have used DEBUG...
Hello,
I am trying to understand the working of BLE Mesh network and have the following question.
Is it possible to make phone as Proxy as well as Provisioner? BLE...
We are planning to build a product based on nRF52811 SoC, which is Bluetooth 5.1 and has AOA and AOD features. Unfortunately, Nordic's hasn't released any new supporting Library...
