When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi!
I am trying to use the NFC " writable_ndef_msg " code along with the " ble_app_uart " code from SDK 15.0 with Softdevice s140 on nRF52840 DK. I am using keil-MDK 5...
How can I be 100% sure the nRF52832 chip is running properly?, what I do to power up the chip is feed it with a regulated voltage of 3.3V (which really is around 3.17V), on...
We use Nrf_studio to connect our board by uart to enter direct test mode.
But an error occurs in serial connection.
I want to know， use our own project program is allowed...
I have already pressed reset in the dongle, it was pulsing red. And when I write it allways says the same error. I have done this experiment in Ubuntu 16.04 and Windows 10...
Dear all,
I'm struggling writing 32 bytes with FDS in SDK 14.
This is what I do:
Init
(void) fds_register(fds_evt_handler);
fds_init();
while(!is_init) {
sd_app_evt_wait...
Hi, I am using nrf51822 Development kit with 3 buttons, each buttons has different functions. (i) 1st Button is used for the wake the module from sleep mode. (ii) 2nd Button...
Hi I using nrf51DK using keil MDK 5 softdevice s110.
I need to update battery level on every 60s and I have initialize timer and start with this code.
static void battery_level_meas_timeout_handler...
I'm trying to implement extended advertising, using BLE_GAP_PHY_2MBPS to offload 255byte advertisement payload to channel data, defining BLE_GAP_PHY_1MBPS as primary phy ;...
Hi
I am trying to broadcast manufacturer data (beacon example) while changing data from second to second. For that I am trying to use timer2 (as timer 0 is used by SD, right...
Greetings,
For Bluetooth Declarations, will new QDIDs be generated to account for the additional required tests as of January 24, 2019 in TCRL-2018-1.
I'm mainly interested...
Hi,
I need to interface LIS2DH through SPI. I tried many SPI Master example but I am getting all the values as 0XFF. Even the WHO_AM_I registers value is getting 0xFF
...
Hi, I have an EMG muscle sensor which needs to be sampled at least 500Hz. Can I sample at the required frequency and transmit at the same time over BLE NRF51822. If not please...
Hi, I am new to the bluetooth mesh concept but I have tried creating one using nRF52 DKs.I have worked the light switch example but I am stuck there without being able to...
Hi everyone,
I bought the nRF51822-04AT module but I'm a newbie and all the documents talk about nRF development kits which they make me confused about programming. Now...
