Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
Hardware:PAC10040
Platform: nRF5_SDK_11.0.0_89a8197
Master Control Panel: V4.1.3
1.If dfu has started and transported some data, then disconnect bluetooth and...
I was able to setup gazell frequency hopping communication between a device and a host. Device:nrf51822+PA/LNA(RFX2401);Host:nrf51822+PA/LNA; They can communicate at a long...
Dear sir,
can you provide any chip which is having RSSI and compatible with NRF24LE1 .We have an application in which we have already have a transmitter based on NRF24LE1...
Hi.
I'm using PCA10028, SDK10.0.0, S130 and "ble_app_uart_c" as reference.
As "ble_app_uart_c" source code, it already knows Service UUID.
uint32_t ble_nus_c_init(ble_nus_c_t...
Hi!
I'm trying to get the MPU-9250 chip working through SPI with my nRF52832. But I don't seem to have much luck.
I have created a basic program for testing, based on...
I am using SDK9.0 to develop a ANCS project,now it accept the incomming call ,message,QQ,Wechat successfully,but the question is how to distinguish the message,QQ and Wechat...
I looked at the radio project in the peripheral folder on SDK5 11. I managed to get a custom radio project that works well with my device. A brief on my project, I set up...
Hi
I have set the nRF Beacon app to action a Tasker task when the phone is "At the beacon".
The app display the following: "An error occurred when launching the task"...
hello
i am using nrf52 board.is there any tutorial to setup the Template project in Visual GDB for the custom design project.i alread test the blinky and the result was successfull...
Hello
I am using this tutorial blog.blecentral.com/.../
to configure my BLENANO to work on eclipse whith gcc toolchain.
I am using the latest SDK which has the softdevice...
Hello,
I can't solved a problem with advertising problem on my iBeacon working on nRF51822.
I have my own 40 unity BLE Module in my room test. They're configured to...
Hello,I run the program nRF52_SDK_11.0.0\examples\peripheral\uart\pca10040\arm4
and rewrite the "main":
int main(void)
{
//LEDS_CONFIGURE(LEDS_MASK);
//LEDS_OFF(LEDS_MASK...
Hi,
nRF5_SDK_11.0.0_89a8197\examples\peripheral\saadc\pca10040\arm5_no_packs
Which timer is used in this example? RTC timer or Timer0-4 ?
I can not find it.
Thanks...
Hi,
I have used nRF51 DK board for 6 months well.
Then now, it isn't connected with nRFgoStudio since I have upgraded nRFgoStudio about 1 month ago.
Error message is no...
Is there any reason I can't have the radio notification run at priority 0? By definition it will never run at the same time as the lower stack, so it seems like I should be...
