I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,
I'm trying to build a Zephyr module that manages some features for a specific board (an SDK for that board). In it, I would like to enable the IPC devices in the...
I am testing data transfer from a microcontroller to a host PC using USB CDC ACM on the nRF5340. Right after powering on the microcontroller, only the first packet takes longer...
hi support team,
do we have any samples on how to show radio statues to gpio? when radio is on, gpio is set to high, and radio is off, gpio is set to low.
waht i can think...
Hi everyone,
I'm in the middle of a project and am starting to run out of available GPIOs.
To save a pin, I was wondering if it's possible to use a single GPIO (for example...
As a detour to getting DFU working for my existing project, based on nRF54L15, it was suggested in a previous ticket that the issue might be with my custom board folder, and...
Hello,
I would like to ask if it is possible to print the status of individual parts of memory on nRF7002-DK while the program is running? So far, I have managed to print...
I am using ncs to develop for NRF54L15. It runs fine on the development kit DK, but it doesn't work properly on my own hardware board. My program always fails to simulate...
Good morning,
I have tried to do the exercise 6 from the nrf-connect-sdk-intermediate course, my nRF9160 devKit can connect to nRF Cloud and download the new firmware. When...
Hello, We are currently evaluating the use of nRF9131 ICs for a mobile DECT NR+ usecase, in which we want to use the position in space of the different participants. Given...
We want to encode audio to LC3 format before we pass it to nrf5340 over USB. Because we know the processing power of nrf5340 is limited. Do you have any support for this?...
Description:
We're using GRTC on the nRF54L15 to implement RTC calendar functionality in our project. During development, we observed the following behavior:
When...
I am developing a Zigbee sensor device based on the nRF52840. I have based my firmware on the "Thingy:53: Zigbee weather station" sample. This means it is a Sleepy End Device...
We have a nrf9160 chip on a custom board with zephyr as the operation system. Modem firmware is 1.3.7. The board is battery powered, but can for development purposes also...
Hi Nordic team,
I am a test engineer at AIROHA, focusing on Zigbee and wireless communication protocol testing. Currently, I am responsible for setting up the Zigbee certification...
