I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
We just received our latest custom nRF52840 board and have found that there seems to be some issue with PO.19. We have verified that the P0.19 is not working on multiple boards...
Hi
Im using the NRF9160 DK
I have got the Asset tracker working, can modify the code, runs with nrfCloud, beauty
Just followed the docs
But then, I want to...
I have to stream packets from an nrf52 to an nrf24 at a 30 kHz rate using ESB. But when I try to do this, the receiver only receives some of the packets. I don't believe the...
I am using ses and trying to set the max payload length or enable debug mode in NRF_ESB.h. I could of course just change the values in the header file, but I prefer not changing...
Hi Community,
I'm a little bit flyiing in the dark, so I like to ask this in the devzone.
Does anyone already implement NFC OOB Pairing and using Apple GymKit?
1...
We are not using the USB interface on the nRF5340, and thus are leaving VBUS and DECUSB unconnected. Can we also leave D+ and D- unconnected?
Thanks,
Scott
To the kind attention of Nordic support team,
I'm interested in understanding in a conceptual way, how the microcontroller is operating when sd_app_evt_wait is called. ...
We have the following setup: - Both nRF52832 and nRF52840 chips in our product
- The nRF52832 is a module while the nRF52840 is the chip integrated directly onto our PCB...
Hi,
Kit:nrf5340
SDK:nrf connect SDK 1.5.0
1.Can you please explain how the data transfer takes place in ble mesh while using nrf connect SDK.
2. Also tell me how...
The servo I use in my application uses a PWM signal duty cycle to represent servo amperage level.
So, to measure servo amperage, I use a GPIOTE channel to capture the time...
Hi!
I'm using ncs v1.5.0 and mfw 1.3.0 on a nRF9160 DK v0.15.0.
I'm using gps sample with supl_clint_library enabled
1. Things work reasonably well, but I am confused...
I'm trying to write a driver for an SPI peripheral.
west says:
```
../ncs/zephyr/samples/sensor/mydriver/prj.conf:5: warning: attempt to assign the value 'y' to the...
new uses SDK 17.0.2, SD 7.2.0
old target used SDK 15.2.0 and SD 6.1.1
Attempting to update BL, SD, and App over DFU.
1. If merging all new BL settings with SD, BL, and...
Hi,
I am using nrf connect SDK and compiling nrf5340 examples.
I want to implement a security related example in nrf connect SDK.
Can you please tell me
1. Security...
Hi,
I am trying to open serial lte modem app to evaluate power profile on thingy91. i am using toolchain manager (v1.4.99-dev1) to open Segger Embedded Studio.
While building...
