hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Hey all
I've some basic question about the Call-Stack.
In my application I have a series of functions which call other functions and so on until an depht of about 20 calls...
Hello. How i can do a simple read an 0 -> 3 Volt (vdd) signal on Analog 0 P0.03?
I try it with saadc without sucess
int result = 0;
NRF_SAADC->CH[0].CONFIG = (
...
Hi everyone, I know that this topic has been mentioned before, but there are a lot of doubts and the situation about measuring a battery is still not clear.
1) First of...
Hi,
Here i are using nRF52832 ,softdevice S132 and mesh sdk v3.0.0
I am facing an issue in UART configuration in mesh (LIGHT SWITCH EXAMPLE) server code . When using my...
Hi all,
I am building Border Rounter and Thread Network. I using SDK 3.1 and image newest for border rounter
I follow this link https://infocenter.nordicsemi.com/topic...
Hello. I am working on a application in a NRF5238 with s132, where I send 20 byte packets using notifications from a peripheral to a central board. The central is a modified...
I updated to SDK v1.0.0 today and have not been able to build sample or application solutions since. I updated the SDK, modem FW, and SES.
For example, when I open and try...
Hi,
I'm sorry to borther you in your holiday.I got a issuse about 52810 (s112) with PA.I found my device would reset when I call ble_advertising_start() after calling pa_lna_init...
I'm trying to implement Serial Wire Debug to read some Data from Nordic from other Controller. Initially Need to read some registers in DP & AP Nordic. For that I need to...
Hi guys, i was using nrf51822 s130 sdk, and now i am using nrf52dk s132 sdk. When i am using nrf_adc.h, all bitfields macro's get errors. It's bitfield macros doesn't match...
I am trying to connect BLE app to BLE Device ( NRF 52840 ) and for security purpose, I adding passcode (password) / key in the device, once I am going for connecting it will...
I used serial program to talk between nrf52 and arduino where the rx tx pins were default 8 and 6.When i changed the pins to 25 and 26 it is not working i am not able to communicate...
Hello
I'm looking for someone to help write a custom bootloader which performs FOTA update by using an HTTP connection to collect firmware. NRF52 is connected to GSM module...
Hello, Dear Support!
I explore examples in SDK 15.3.0 : ble_app_hrs and ble_app_rscs. The peripheral device in ble_app_rscs is configured to wait active request from central...
