I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hi all. I would like to get the current RTC tick when there is an advertisement RX event on multi-link central. I am going to store the advertisements along with a time i...
Hello, In one of my codes, I use the printf function. It works properly when implemented in the int main(void), but when I try to use it in a static void NAME (void){} function...
Hello,
I'm checking the DTM code from nRF5 SDK15.2.0.
In the ble_dtm.c file, line 763:
And in the ble_dtm.h file lines 104-110:
DTM_PKT_0XFF and DTM_PKT_VENDORSPECIFIC...
Hi.
We got Thingy for power measurement purposes. I tried first the it out of box and it works fine. Same with pre-built image.
However if I build the SDK example and...
non connectable advertise success when in SDK 8.0.0, however I got error code 0x00000007 when upgrade to SDK 9.0.0.
I find out error code 7 is NRF_ERROR_INVALID_PARAM,...
hi,
my development kit nrf52832 is not detecting via phone nrf connect app . it appears like no device found .i flashed the ble blinky example program (sdk 15.2version)...
Hi to everyone!
I recently bought the nRF52 SDK to use it in a project, but the kit contains a NFC antenna and I don´t know its use.
My project its about Bluetooth Mesh...
i use the sdk15.2.0, the chip is nrf52832,my device have both BLE peripheral,and BLE center in my application, I use center to connect with peripheral, i directly use the...
HelloI am trying to program nRF52832 QFAA and am succeeding only partially: the debugger is connecting to the chip, and I can RUN step by step, however, I'm seeing only the...
Hello, I have adjusted the Uart Central Example from the SDK 15.1.0 with the stack s140 v6.1.0 so that the device can connect to two peripherals. The name of the device is...
Hi All,
I use SDK 15.2 to periodically trigger ADC acquisition tasks via PPI. But SOFTDEVICE: INVALID MEMORY ACCESS error occurred while the system is running.
I found...
I am using nrf52832, SDK v14.2, Softdevice s132_nrf52_5.0.0.
I had program the softdeive in flash, and I program the DTM firmware as application(start address set as 0x23000...
Hi Guys,
How do I configure Embedded Studio to generate full build log output? For example I want check whether all the header I included is compiled correctly.
Please refer back to the original link
The reason for this massive edit is because this post included code I tried to reconstruct from memory at home with only the SDK sources...
Dear team, We are getting an error in running the Android app in the background: ' Service destroyed '. It comes when the app is minimized and use any other app after that...
