Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Looking at the ble_nus service, I see that the SoftDevice allows notifications to be more than 20 bytes long:
uint32_t ble_nus_string_send(ble_nus_t * p_nus, uint8_t *...
I'm try to use RTC1 to generate overflow interrupt, but it doesn't trigger interrupt.
void RTC1_IRQHandler(void)
{
// do something
}
main()
{
NRF_RTC1->TASKS_STOP...
Hi,
I'm using s132, sdk 12.1 on nrf52x, my question is about possible race condition when setting the value of a characteristic using sd_ble_gatts_value_set (on peripheral...
Hi,
I am working on a IoT based project with nRF52832 and nRF52840. I am looking for PCB Designers and people who can develop firmware for our project. The firmware development...
Hello, in S110 device's nrf_sdm.h, there is this enum "NRF_CLOCK_LFCLKSRCS" which is defined as:
enum NRF_CLOCK_LFCLKSRCS
{
NRF_CLOCK_LFCLKSRC_SYNTH_250_PPM, /**< LFCLK...
Hi..!
I am trying to ***Receive ACCELEROMETER DATA FROM MPU6050 to PCA10028(NRF51822) AND WANTING TO PRINT IT ONTO UART using KEIL IDE.
Code is getting compiled & getting...
HI.
I want to send data from nRF24L01 + to RF communication and receive it from nRF24LU1 +.
The nRF24L01 + is connected to the STM32. The settings are as follows.
...
Hi, I'm trying to build a bluetooth device that pairs once, and does not have other hosts maliciously or accidentally pair to it (which would create a poor experience for...
Hi,
When i used nrf51822, i remember the s110 define max transmit buffer as 23 Bytes, but now, i am using nrf52832, the max transimit buffer is defined as 158 bytes.
Does...
Hello, I understand this may be a very broad question, but I still need to find as much information as I can.
Give a general answer if you'd like to, or a very specific...
Hi,
I just got the email about SDK13.0 official release. The list of changes in this release include "Secure DFU improvements". What does it mean?
Is Buttonless Secure...
Hi Engineer!
I would like to use DTM mode to test nrf52840 in our pre-samples.
but i did not find any info about that. how to use DTM in this chip ?
thanks you!
I've recently migrated from SDK11 to SDK12.3 using a FreeRTOS based applications. I seem to get a hardfault on a sd_ble_gatts_hvx call. There is no difference between my SDK11...
