Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi! I want to send data from the temperature sensor of the beacon, receive them with the nrf51 and then send them to the PC via USB cable. The nrf51 has to start the connection...
I am using the nrf51822 and I want to use the pstorage library to save some data which is "power lost can save",but I cloud not find the example of it.I am using the SDK 8...
Hi,
I want to have a generic fault handler that will cause a reset. The handler may be called from a high-priority ISR or exception trap (e.g. hard fault handler), and...
Is it possible to make a services like this：
services UUID : 55550001-5555-5555-5555-55555555555
characteristic UUID : 55550001-4444-4444-4444-444444444444
Hi All ,
I am using NRF52 , S132 softdevice ............
I need to read a data every 5s (In Timer1 interrupt handler) from I2C slave and sent it via BLE.
But what...
Hello,
How do I create an encrypted/signed image? Where can I find the documentation for doing this? How will I need to modify the bootloader to decode and install the...
Hi All,
I am using Nordic SDK version nrf51_SDK_9.0.0 for PCA10028 board. In that i am using application
D:\nRF51_SDK_9.0.0_2e23562\examples\ble_central_and_peripheral...
Hello Everyone,
I have developed my software and i have tested with NRF51DK using android phone NRF MASTER CONTROL PANEL APP and it is working very well but now am trying...
Hi Nordic,
On SDK10.0 with QFACA nrf51, I find a GPIOTE problem.
With sdk6.1 and app_gpiote module, I got no such problem.
I make use of SPI0,low accuracy GPIOTE on 4...
Hi.
I'm using PCA10028, SDK10.0.0, S130.
I'm testing connection time.
I made structure as your sample code as below.
static const ble_gap_conn_params_t m_connection_param...
I am using nRF52 SOC.
I would like to use BLE to transfer files between BLE client and server. I was hoping to find an example of the OTS implemented in the SDK but couldn...
I opened, compiled, and uploaded the UART example on my nRF52-DK board using KEIL IDE. I use either CoolTerm or RealTerm on my PC. When I open the Terminal program I can see...
I Just upgraded my RTE to the latest two minutes ago, and tried an RTX example.
The example compiled OK, But in RTE manager, it is showing missing component.
Screenshot...
Hello!
I'm in doubts about proper configuration of GPIO pin, which I'd like to be able to reset external device (DWM1000), connected to nRF51 by SPI.
The datasheet says...
Hello,
I’m working on my own custom board based on the nrf52832 (QFAABB).
Here the schematic:
I succeed to flash the board with the nrf52DK (PCA10036) via the debug...
