Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
HI,I want to send multi packets per connection interval. I have checked some questions and thread.
like this link text
and this link text .
according to the example...
Hi Team,
What if I don't what to use BLE stack but still want to use nRF51 Radio (PHY + MAC) to implement some custom communication protocol between multiple nRF51 devices...
i am new at this so please bare with me.
i was using a nfr51822 with s110 version 7 and i now i want to migrate it to s110 version 8.
i have made a few changes according...
After checking bootloader example from the SDK version 10, I am not able to find appropriate ROM / RAM addresses configurations for 16kb RAM chip. The Bootloader examples...
Trying to run S130 V2.0.0 with ble_app_proximity on a BLE400 motherboard.
Im getting a hang at the call to SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_SYNTH_250_PPM, NULL...
Hi,
We just received our custom board based nRF52832, below nRF52832 schematic
I succeed to flash the board. but i have frequency troubles.
I made a simple exemple...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I have opened the nordicID sample project "InventorySample" for Windows CE in VS2008 it successfully builds the project but when i deploy it on mobile simulator Pocket PC...
Hi,
I'm using S132 v2.0.0 and nrf52832. I've got a problem when I'm trying to call any softdevice function from radio notification event handler.
#define RADIO_NOTIFICATION_IRQ_PRIORITY...
I am using nRF52832 DK and we designed a custom board using nRF52832. I am using a windows 10 lap. It used to program successfully from windows 10 lap and boards will advertise...
Hello,
I use nrf51 based device as peripheral with SD110.
I use connectable advertising ( BLE_GAP_ADV_TYPE_ADV_IND, BLE_GAP_ADV_FP_ANY ) and turned on BLE_GAP_EVT_SCAN_REQ_REPORT...
Hello,
what address in flash is it safe to store my application settings (some calibraton data) which should be preserved during application updates. I use S110 v8, dfu_dual_bank_ble_s110_pa10028...
Hi all, i'm trying to understand how to program my nrf51 DK in order to perform a temperature measurement with the onboard sensor, convert the battery voltage with the ADC...
I use dfu_dual_bank_ble_s110 bootloader from SDK10. I want the bootloader to check whether if incoming firmware is compatible with the device it is uploaded to (i.e. device...
Hi
I want to connect to only a single master device by s110. I used the example parameter setting from "ble_app_hids_keyboard" for gap_params_init, advertising_init and...
