I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
I have two mic , how can I get data from Left and Right mic? Is there any example code to help me?
My code like this : ( I think the data from pdm_data_handler is like 0xFFFFxxxx...
Hello,
I am using Seeger for flashing Code and Debugging. I ported code from “flash_fstorage” example code to “ble_app_blinky”.
In “ble_app_blinky”, as part of wait_for_flash_ready...
Hi,
How can I port the code written for nRF51 to nRF52>
Do have nRF52 FW backward compatibility.
And can i use same base code for both chips?
Is there any link/documentation...
Hi, I am testing NB-IoT on the nrf9160 and it appears the DNS is failing.
I have two networks here and with an NB-IoT modem from a different manufacturer the DNS is resolved...
Dear NRF gurus,
We are trying to implement a BLE node to bridge BLE 5 and BLE 4 - to leverage the long range of BLE 5 in the meanwhile working with the large amount of existing...
hello everyone, i am looking for the maximum allowed deviation of the uart. The nRF52832 is clocked with 32 Mhz and has a baud rate of 19200. What is the maximum deviation...
Hi
I am working on BLE Eddystone example program in nRF52832 using SDK 15.3.0.
can i change the password entered in the nrf Beacon for Eddystone app into ascii value.
hi ...
i want to connect multiple peripheral to one central , want to share the data. so i have merged the multi link central with central uart . while i am compiling i...
hi,
i am trying to integrate nRF SDK 15.3's ble_app_buttonless_dfu service in ble_app_blinky example,
after adding all source files and and preprocessor definitions while...
Hi,
we are using a custom nRF52840 board with SDK 15.0 and softdevice S140 6.0.0. Flashing the application including DFU and softdevice using SES produces the following...
I have a strange problem running the CLI example in the DK on the Nordic dev board with SES: It works fine with build/run, but when trying to debug it pops up a message that...
I am using the nRF52832 in several projects for several different clients. I have created a "project" under Visual Studio using VisualGDB for each one, using the automated...
Hi,
I would like to know how to raplace a MPU-9250 chip with ICM-20948 in a Thingy:52 circuit.
Let me first state that my electronics engineering knowledge is at hobby...
So I've had a LOT of problems getting power management to work with UARTE on the 52840. We're using both UART_0 and UART_1 and have finally gotten UART_0 to work as it should...
