Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Hi,
I'm currently testing ble_app_uart on nRF51822 custom board. I connected it to nrf51 DK P19 and was able to program the hex file successfully.
But it doesn't run...
Hi, In your documentation you specify the maximum CPU temperature 85 DegC.
What problems could one expect after this point?
How much safety margain du you have on this number...
I'be been reading over and over the datasheet but cannot see how to dissable Enhanced ShockBurst features for my application which only requires basic one way radio.
I...
Hello,
I'm trying to program that module, but i can't do it correctly.
I'm using a program that works fine in nrf51 DK, but when I program this in ptr5518 my smartphone...
I want to port either the S210 experimental DFU over ANT_FS to serial DFU or the S110 dual bank serial DFU project to be S210 compatible.
I'm using S210 V4 and SDK 8
...
I would like to connect more than 8 devices to a single host. Therefore I would have to set the same role to multiple devices.
What are the implications of using the same...
HI,
I have some problems with the function sd_ble_gap_scan_stop(). I want to stop scanning into the RTC1 event handler but when I use this function (sd_ble_gap_scan_stop...
HI:
i have a question.if i use 51822 to connect other ble(ti or csr) ,could that be achieved.i have used ti dongle to scan 51822,but can't found 51822 device.if 51822 connect...
Hello,
In our project we use HID service. The difference between our HID and standart HID is that we use our own UUIDs. Our report charactestics include Report Refernces...
I'm having trouble compiling the pc-ble-driver ( github.com/.../pc-ble-driver) on windows. Some help debugging the problem would be greatly appreciated. It might be an issue...
Hi,
I am using SD110 V8.0.0, SDK 8 and chipset nRF51822 QFAC.
Sometimes my app get assert error from file A\a with random error code and 0x0000000 line number. How to...
I use the software 1.0.1.478.0 release. Is it functional with V1.0.4 plugin ?
When I generated the following message code is displayed :
" Nordic Semiconductor nRF51 plugin...
I am trying to setup a multiceiver scenario with the nrf24l01+ with three transmitters (PTX1,PTX2 and PTX3) and one receiver (PRX) with enhanced shockburst but I am having...
Hi,
I'm trying to use winbond spi flash (w25q64fv)
but i have a problem with spi as you can see in below image clock stop before receiving data from spi flash, do you...
