I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
We are using Thingy:91 X as an evaluation platform for our upcoming product. Our test application is made up of a nested-loop structure like
while(true){ lte_lc_connect...
I'm using the code below to trigger a callback on pin rising edge.
Unfortunately, the counter is not being increased at all. Any reason why? I used multiple sources already...
Hello Team,
I AM USING NRF52833QDAA IN NRF CONNECT SDK , IN DATASHEET P1.09 IS MENTION BUT IN OVERLAY FILE OF NRF52833QDAA AT ALIASES PIN P1.09 IS NOT MENTION OR NOT DEFINE...
Setup NRF52840 with SDK 17.1
FreeRTOS tickless idle mode
When we call xTaskNotifyWait and then get the notification then function returns but the result of the function...
Hello, I'm testing the nRF21540 FEM on a custom nRF52840-based board using the nRF Connect SDK.
I’ve enabled CONFIG_MPSL_FEM CONFIG_MPSL_FEM_NRF21540_GPIO_SPI CONFIG_BT_LL_SOFTDEVICE...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
Hello Nordic Team,
we’re evaluating nRF91 for our next product platform (being strong in LoRaWAN since years) and hoped to quickly run some first field trials with the recommended...
We have been using wget to get nrfutil on CI. Today it stopped working. Giving error " ERROR 403: Forbidden " The same link still works on browsers. The link is: https://developer...
Hi,
We're running into a high memory usage issue on an application that is using the nRF5340-nRF7002, multiple sensors on SPI, SDC with littleFs, BLE and WIFI. The WIFI...
Hi,
I'm currently working with a nrf6191 on a custom board using Zephyr and I would like to use little FS as my file system.
So far I've set the configuration and overlay...
Hi,
As the title states, after a while, the nRF7002 fails to connect SSID after a while. It happens either we perform net_if_up/down or not. I suspect the nRF7002 to be...
Hello,
I’m developing a project using the nRF52832 and I’d like to put the MCU into the lowest possible power consumption mode while still being able to wake it up via a...
Hello, checking if I'm doing this right of restoring initial fw for 91X to work with Quick Start v1.2.0. as described here in Get Started, https://www.nordicsemi.com/Products...
I have devices that manually define PDP context 0 in order to set the APN to the required value for the SIM.
Typically, once connected to the network, the IP address gets...
