The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi everyone,
I am trying to understand the GATTS Handle Value Notification diagram.
From what I have understand so far is tha the soft device keeps a buffer (ATT table...
Hi engineers,
I want to implement function that input i2s data and then output it directly.
I find that i2s demo includes two buffers which are used for current buffer...
Hi,
I want to verify
1. Program ble_app_hrs with buttonless dfu integrated + secure bootloader + bootloader setting to nRF52DK.
2. Boot up nRF52DK, then use buttonless...
I don't know what happened to my thingy 52 after lots of firmware updates with Keil+Jlink+thingysdkv210 and nRF connect operations. The LED on thingy isn't flashing any more...
Hi engineers,
I want to use saadc to measure the battery's voltage, but the result I get is incorrect.
So I use the saadc demo of the nrf5_sdk17, then I measure GND(negative...
Hi. I am trying to use PIN 0.19 as my SPI CLK but it is always low.
Previously, I tried to change the pin to 0.26 and it works.
Is there any other configuration required...
Hi Nordic
SInce this is my first time to develop Nordic chip and implement SPIS driver, Therefore i am not so familiar with Nordic API. I would really appreciate it if...
HI,
I want to upgrade the BL in APP directly. I encouter a wierd problem. When APP erase a specific page of the BL(the address is 0x74000), the system halts. If ignoring...
Hello,
I am using nrf51822/SDK 12.3/sd 130.
An error occurred while implementing nus_c using multi-role example.
Error 7 occurs in sd_ble_gap_conn_param_update() frequently...
Hi,
I used Jlink Edu successfully to flash the asset tracker code using segger. but when put the breakpoint it went to some different file.
I have a quick question regarding...
I have just received an nRF52833-DK and am trying to get started with it.
I am at the website:
https://www.nordicsemi.com/Software-and-tools/Development-Kits/nRF52833...
Hi,
I press Button 1 and Reset to put the nRF52840 DK in to DFU mode that is programmed with a immutable bootloader (B0), mcuboot, and application. This works well to...
Hey. I am new to this forum and new to programming BLE chips. I have ordered my first dev board and cant wait to get my hands on it. I have been reading a lot for the coupe...
Guys,
I am currently experimenting with an existing wearable that contains an NRF52832XXAA Revision 1, and I'm having a hard time to have it running a simple BLE peripheral...
Hey everyone! My team and I are working on making a hex file that contains the soft device and software, as found in the 15.3.0 SDK, in the secure dfu test images folder....
