Hello,
We have an issue. Our device is a custom board based on the nRF9151, and we use it in Latvia. Two network providers are available for our Onomondo SIM card: one supports...
We are seeing the same thing as in 129099 (case 362913) and 129410 , found independently on our side. We have narrowed it down a bit further, so we open a new thread with...
We are investigating an intermittent Bluetooth Mesh LPN issue on the nRF54L15, where the LPN state machine becomes stuck in BT_MESH_LPN_ESTABLISHED even though the Friendship...
Hello,
We are developing a product based on the nRF52840. According to the blog post nRF Connect SDK gets Long-term support with version 3.4.0 , NCS v3.4.0 declares the...
Subject: Request for Optimal Battery Solution for nRF54L15 Matter End Device
Hello DevZone Team,
I am opening this ticket to identify the optimal power solution for my...
Hi,
On the nRF93M1 DK, we can switch between physical SIM and eSIM with %SIMCFG="SimSlot" (mfw 1.5.0).
1. Is SimSlot written to NVM on set, or in the flush at CFUN=0?...
Hardware: nRF21540 DK
SDK Version: NCS 3.4.0
Problem Description:
Modified the observer sample to scan for a specific device, using nRF21540 DK as the scanner with FEM...
Hello -
I am trying to print a 64-bit unsigned integer (uint64_t) to a CLI output. I've based this on the CLI examples in SDK 17.0.2. Specifically this is the function I...
refer to: http://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_multi_image.html developer.nordicsemi.com/.../partition_manager.html
Where I change those image...
My accelerometer readings appear in my segger embedded studio "Debug Terminal" window.
It looks like this.
I want to stream the data via COM port to this "serial oscilloscope...
~/ncs/nrf/include/dfu/dfu_target_mcuboot.h int dfu_target_mcuboot_done(bool successful);
/////////////////////////////lack of this in last #ifdef __cplusplus } #endif
I am using mesh SDK v4.2.0.
I read the documentation of the remote provisioning example (pb_remote) and took look at the code.
My first feeling was that the remote provisioning...
To the kind attention of Nordic support team,
I'm working on a nRF52 based product, I saw using your sniffer that after LL_CONNECTION_UPDATE_REQ
I have got a Window Offset...
We have an nRF52 DK and have developed a customer board. On the custom board we have a header with pins for power, ground, clock, and data.
When I connect this to the nRF52...
Hi,
I've got ANCS working well in my application, but I seem unable to increase the length of the notification's message that I receive.
BLE_ANCS_ATTR_DATA_MAX is defined...
Dear sir,
I have an two problem:
1) Once change the device mane, after system rest some junk value is stored Note : here the device name read from the flash memory ...
I'm trying to run Provisioner Example on my nrf52840 DK, which is in examples/provisioner directory, . First I've build softdevice on DK and then I'm trying to build provisioner...
Hey NordicSemi. In my new project, I use DK NRF9160 and I need to determine the location. Since hardware GPS does not work, I decided to use the detection of coordinates through...
Hi,
Something locks-up my I2C sometimes and I need to make I2C recovery. It looks like Nordic has not implemented the zephyr i2c_recover_bus function, so I guess I need...
I'm looking for dual core inter task communication examples
where a thread on one core is interacting with a thread on the other core ?
e.g. will there be some kind of...
Hello All,
I was looking at the Digi XBee3 modules for a ZigBee project I am working on. What is great is they allow you to write MicroPython code to control the network...
