Hi, Our nRF52840 (NCS v3.4.1, SoftDevice Controller) is a central that connects to smartphones running our app (phone advertises, nRF52840 initiates). About 12% of connections...
I'm in the early stages of building a Thread + CoAP low-power sensor and using the nRF54L15-Tag as a starting point. Using NCS, the lowest idle current I can get is 13 microamps...
We are currently evaluating the nrf9151 via the thingy91X
for our application we need the device to function in areas with no cell coverage and not drain the battery....
Hi
SDK: ncs-v3.4.2
I wanted to compile the lesson as a starting point for a product in non-secure mode with TFM.
I don't have the nrf5340dk but one with the same chip...
We will like to use the Nordic nRF9151 to verify our CP-EDT feature. For that we need an AT command to trigger MO ping but we have not been able to find such command in your...
Hardware: nRF21540 DK
SDK Version: NCS 3.4.0
Problem Description:
Modified the observer sample to scan for a specific device, using nRF21540 DK as the scanner with FEM...
Hello,
Recently we're planning to start our nRF-9151 custom board production.
I've designed my own PC program to confirm all the connectors out application used are doing...
I understand that the nrf9160 product is still in pre-release. I did have a look at the gps receiver section in the DocLib.
For future planning it would be very helpful...
I am setting up a custom hid device bulk transmission, which can normally send data to PC at present, but cannot receive data from PC (no data interrupt was received in the...
I am able to use the 2 channel mode of each PWM giving me a total of six PWM that I can set individual duty cycle PWM!
I now find I need 8 PWM with individual duty cycles...
I see that BBC Micro:bit uses nrf51822 and can use RADIO peripheral.
So I tried to make my nrf52832 DK to talk to Micro:bit by using Gazell library and referencing MicroBitRadio...
Hi,
We are using SDK14.2.0 and getting assertion failed error with id = 1, pc = 0xEAC2 and info = 0.
What can be the cause of this error?
Thank you in advanced.
The function model_timer_elapsed_ticks_get() returns the total number of ticks since the timer was started. Hence it's expected that this function to return a value > 0 when...
I am attempting to do the LTE_Gateway example. I have gotten all the code to build through Segger and upload to the DK. The problem is when I'm watching the terminal for the...
Dear All,
I am using NRF52840 DK with SDK13.0 . I am trying to use one SAADC channel (CH 1) to record input signals at 200 kHz to fill a buffer of 2000 points . After the...
Hi
I was playing around with the new SDK 15.3.0 and most things worked as expected. One thing that causes some trouble is the changed MBR parameter page handling. It seems...
i need to generate an irk from nrf52 so that no device can identify that nrf52 data...only the device with same irk can identify and connect to it
for that what should i...
I am trying to port Keil code to SES 3.40 with NRF51822 Device and SDKV12_3, I am currently using the ble_app_uart example. I followed this blog post https://devzone.nordicsemi...
Hi Sir
Is it possible write a hex file to external QSPI flash by nrfjprog ? if yes, please tell me what's the command ? Thank you.
ps, the hex file is data, not firmware...
We are using nRF52840 SDK 15.0 with Segger embedded studio. We have referred ble_app_proximity example only for read battery level using ADC. Now in our application used SAADC...
Hi, I m using nrf 51822 development board. I want to implement timer in input mode to detect falling edge of the pulse.. It should give intrude when any falling edge is detected...
Hello
I am a big fan of Zephyr OS, and have developed several commercial products with it (on other NRF chips)
I would like to know if the nrf9160 is to be supported...
