Hi Nordic Support Team,
We are investigating an intermittent Bluetooth Mesh LPN issue on the nRF54L15, where the LPN state machine becomes stuck in BT_MESH_LPN_ESTABLISHED...
Hello,
We are developing a product based on the nRF52840. According to the blog post nRF Connect SDK gets Long-term support with version 3.4.0 , NCS v3.4.0 declares the...
Subject: Request for Optimal Battery Solution for nRF54L15 Matter End Device
Hello DevZone Team,
I am opening this ticket to identify the optimal power solution for my...
Hi,
On the nRF93M1 DK, we can switch between physical SIM and eSIM with %SIMCFG="SimSlot" (mfw 1.5.0).
1. Is SimSlot written to NVM on set, or in the flush at CFUN=0?...
Hello, I've built sample aws_iot for target nrf54l15dk/nrf54l15/cpuapp, using the provided .conf & .overlay files for nrf54l15dk using NCS 3.4.1. The certificates and keys...
We feed the nRF54LM20A’s VBUS pin (the USB high-speed PHY) from the nPM1300’s VBUSOUT, so that the PMIC’s input protection guards the module and the processor sees VBUS only...
I have two nRF9151 DKs and want to evaluate direct, SIM-free DECT NR+ communication using FT and PT roles. Please help me with:
- DECT NR+ MAC/PHY modem firmware, rather...
Hello,
I am using pca10028 and sdk 12.2. I want to scan the nearby ble devices and want to display the mac address using uart. So which code should I refer or which thread...
I am doing some custom work, and have discovered an odd bug, that I can not seem to figure out.
On the tx radio, I am transmitting a BLE ADV packet with the first 3 bytes...
On nRF52, I see that 100 kHz gives a SCL period of 10 us which is correct but for 250 kHz, I get 8 us instead of expected 4 us. Similarly, for 400 kHz I only see 5 us instead...
I have a case where a module that can perform bit clears in the UICR needs to execute while a Soft Device is present and enabled.
I am aware that any direct flash access...
Hi Nordic and fellow developers,
I have been working on upgrading the nRF51822 QFAA s110 and upgrading the soft device to work as s130 for its (simultaneous Central/Peripheral...
Hello!
I'm trying to read data off of a commercial blood pressure monitor (Qardio arm) using an nrf51822 with the nrf51 SDK v10.0.0 as the central role (s120). I am able...
Hi,
we are using nRF52832 and running into memory issues as we add functionality.
It would be great if the '40 was available as a drop in replacement in WLCSP package...
Hello.
I want RSSI check. so added source code as below.
test_rssi_start = sd_ble_gap_rssi_start(m_conn_handle,BLE_GAP_RSSI_THRESHOLD_INVALID,0x00);
if(test_rssi_start...
Hi all,
Is possible using NFC to send variable message? I want to send a counter event (data I got via BLE) to the NFC module.
Using the example I was not able to do...
Hey,
I'm just wondering how to add a UUID to the blinky example peripheral?
I want something like the heart rate sensor where its advertising BLE_Heart_rate_sensor.
I...
We have recently migrated from a custom board based on the nrf51 to a new board with the nrf52832. Our nrf51 board used to run at 6-8 uA when it was just sitting there advertising...
Hi
During schematic design, i read regarding proper powering of NRF52 (the product is battery powered 2xAAA). somehow i can't find this info now and i would like to verify...
What does mask and 1<< mean in the following code:
#define BSP_LED_0_MASK (1<<BSP_LED_0)
#define BSP_LED_1_MASK (1<<BSP_LED_1)
#define BSP_LED_2_MASK (1<<BSP_LED_2)
...
Hi all,
I'm transferring data to and from an Atmel AT25040 NVRAM using SPI, and it works perfectly when run within main(). However, if I run the same code from within an...
