Thread border router - IPV6 DHCPv6 problem

[Carry Irving]

Hi there,

I'm using ASUS RT-AC1900P router with IPv6 DHCPv6 on. RPi gest its own IP with prefix specified in router but interface wpan0 (wpantund) not. I have configured the Router properly, the static IPv6 with /62 prefix. My RPI seems to get the prefix successfully, But my Thread nodes don't have an IPv6 address created using /62 prefix. My border router works on v0.11.0-1.alpha firmware. How can I solve this problem in this case?

eth0      Link encap:Ethernet  HWaddr B8:27:EB:F7:52:E6  
          inet addr:192.168.2.204  Bcast:192.168.2.255  Mask:255.255.255.0
          inet6 addr: 2001:250:4000:1230::1bec/128 Scope:Global
          inet6 addr: fdb3:867c:4acf::1/64 Scope:Global
          inet6 addr: fe80::ba27:ebff:fef7:52e6/64 Scope:Link
wpan0     Link encap:UNSPEC  HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00  
          inet6 addr: fdff:cafe:cafe:cafe:38b0:d362:515:aa91/64 Scope:Global
          inet6 addr: fe80::38b0:d362:515:aa91/64 Scope:Link
          inet6 addr: fdde:ad00:beef::98e0:3f4c:428b:abc4/64 Scope:Global

> ipaddr
fdde:ad00:beef:0:0:ff:fe00:c000 
fdff:cafe:cafe:cafe:df20:60c:6f0a:de9c 
fdde:ad00:beef:0:8625:f5f0:b3df:6f10
fe80:0:0:0:d4ed:2599:a745:c938
Done

Thanks. xiangcai

[Carry Irving]

I've noticed this thread, but it didn't work for me.

[Jørgen Holmefjord]

Hi,

From your ifconfig output, it is clear that your border router have not been assigned a /62 or lower prefix address for eth0:

inet6 addr: 2001:250:4000:1230::1bec /128 Scope:Global

Are you running stock firmware on your ASUS router? I see you have seen my comment in this thread. As I said, on many routers DHCPv6 does not work correctly and they are only providing /6 4 prefix or higher addresses. You should try OpenWRT on your router (if supported), or try with a router that correctly assigns IPv6 addresses with /62 or lower prefix.

Best regards,

Jørgen

[Carry Irving]

Thanks for your kind help, I will have a try.

[Carry Irving]

Hi,

Does it work if I assign a specific static ipv6 address with prefix length to that interface? Such as modify the file `/etc/config/network` like the following shows:

config interface 'wan6'
        option ifname 'eth0'
        option _orig_ifname 'eth0'
        option _orig_bridge 'false'
        option proto 'static'
        option ip6addr '2001:1234:4567::2/48'
        option ip6assign '62'

root@OpenWrt:~# ifconfig
eth0      Link encap:Ethernet  HWaddr xxxx
          inet6 addr: 2001:1234:4567::2/48 Scope:Global

I had tried it, but Thread Nodes didn't have an IPv6 address created using /62 prefix. Why?

Thanks~

[Jørgen Holmefjord]

It was a bit unclear from your last comment if you set the static address on the router or on the boarder router? Could you provide the log generated by the command "ip -6 route" on the border router? It should help us determine if you have the proper prefix in the routing table. What prefix do you get from your ISP? Did you flash your router with a custom firmware (OpenWRT, etc.)?