Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
UART Hardware Flow Control 0

Hello Nordic community, using nrf5-sdk for nrf52840 SoC, I followed the uart example as below. The uart tx and rx works fine BUT NOT THE HWFC eg. When the CTS is set...
56 views

0 replies

Started 22 hours ago
by maveli
Not Answered
What are the features, performance, and usage limitations of the built-in GNSS and 4G in the nRF9151 NTN module? 0

Hello, We are currently designing an NTN satellite IoT terminal product based on the nRF9151 NTN module, primarily for tracker-type applications. In addition to NTN satellite...
- Evaluation
- nRF9151
- NTN eval
- hardware
94 views

0 replies

Started 1 day ago
by Baoxiang
Not Answered
Clarification on nRF21540 FEM TX Gain Selection (CONFIG_MPSL_FEM_NRF21540_TX_GAIN_DB vs MODE Pin / POUTA & POUTB) 0

Hi Nordic Team, Below are the configurations that I have done for the nRF21540 FEM. .config file # # Multiprotocol service layer (MPSL) # # CONFIG_MPSL_FEM_ONLY is not...
62 views

0 replies

Started 1 day ago
by Uma Maheshwar Reddy
Not Answered
nPM1300 EK charge‑discharge profile logging abnormal at 45 °C 0

Excuse me. When the customer uses the nPM1300 EK for battery charge‑discharge profile logging, after charging completes at 45 °C and the USB cable is unplugged as prompted...
98 views

0 replies

Started 3 days ago
by Mason Bu
Not Answered
PWM in nRF54L15 with power management 0

Sorry, this post is deleted.
764 views

0 replies

Started 9 months ago
by Gujju

Recent in the DevZone Blog

Writing BLE firmware with a few lines of code

Nguyen Hoan Hoang

Writing a BLE firmware can now be done with a few lines of code. The code example bellow is all you need to write for a non-connectable BLE firmware that advertise a counter value every second in the…
- 29 Dec 2017
nrF52 Tutorial: ETM Instruction Trace with Keil MDK

Bob Boys

Hello I wrote a tutorial on using the nrF52 Development Kit with Keil MDK. www.keil.com/appnotes/docs/apnt_308.asp This document features essential debugging capabilities of the nrF52 series. ETM Instruction…
- 15 Dec 2017
One minute to understand BLE connection data package

viewtool

1.Profile During connection procedure of BLE, there are three packages: SCAN_REQ, SCAN_RSP 和 CONNECT_REQ。 SCAN_REQ： Scan request, issued by MASTER DEVICE, send to SLAVE DEVICE，sent by the Link Layer…
- 15 Dec 2017
One minute to understand BLE MTU data package

viewtool

1.Profile MTU: ATT Maximum Transmission Unit (MTU) is the maximum length of an ATT packet. The ATT MTU is defined by the L2CAP and can be anywhere between 23 and infinity. The implementation of the Bluetooth…
- 15 Dec 2017
Debugging on nrf52840 with GDB from CLI on linux

jfcamel

Today I tried to find the better ways to debug program on nRF52840 PDK from CLI on linux. The ways that I tried [Failed] openocd (both stlink and jlink) & gdb [Succeeded] JLink & JLinkGDBServer &…
- 14 Dec 2017
The KEY POINT of example "ble_app_uart"

QQ645116977

This article baed on "pca10040", nRF52832 example code path "examples/ble_peripheral/ble_app_uart" IMPORTANT!!!! board config file of this example located in "components/boards/pca10040.h" and uart…
- 12 Dec 2017