Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
PPK2 calibration offsets corrupted in EEPROM 0

Hello, My PPK2 (PCA63100, rev 1.1.2, build code 2026.8) reports corrupted calibration offsets: O0 / O2 ≈ 4.06e31, O3 ≈ −2.8e15, O1 / O4 ≈ 0, and the Power Profiler app shows...
5 views

0 replies

Started 6 minutes ago
by MarcoR
Not Answered
fs_mgmt file-upload write ACKed at link layer but never reaches Zephyr host (bt_recv_unsafe) on nRF54LM20A — related to IOS-nRF-Connect-Device-Manager#659 0

This is long and AI generated. Sorry about that, but it is comprehensive. I'm seeing a very specific, repeatable failure uploading a file via mcumgr's fs_mgmt over BLE,...
15 views

0 replies

Started 1 hour ago
by lcj
Not Answered
SoftDevice Controller / MPSL BabbleSim libraries for NCS v2.9.0 0

Hello, We run our Bluetooth Mesh product firmware in BabbleSim, on a simulated nRF52840 (nrf_hw_models, native simulator). We are on nRF Connect SDK v2.9.0. We would like...
19 views

0 replies

Started 1 hour ago
by Denis_Linkio
Not Answered
nRF54L05 wake on I2C standby current 0

An external MCU occasionally sends data to the nRF54L05 over I2C. Between transfers, the nRF54L05 should sleep and wake when addressed, without a separate wake pin. What...
58 views

0 replies

Started 19 hours ago
by Jonsiann
Not Answered
Thingy:53 Zigbee End Device — Configure Reporting failures + malformed Report Attributes flood 0

On a custom Zigbee End Device application for the Thingy:53 (NCS v2.9.3), ZCL Configure Reporting commands sent by Zigbee2MQTT are rejected with ZCL status FAILURE for almost...
- development
- software
- debugging
- zigbee
- zephyr
- nRF5340
54 views

0 replies

Started 20 hours ago
by Gabor Bohm

Recent in the DevZone Blog

Start Up Extreme Norway

John Leonard

Last week I attended what was my first Startup event, but after experiencing the energy there, I can safely say it will not be my last. 3 days of seminars, networking and lots of fun kicked off in Bergen…
- 22 Jun 2015
Step by Step Guide to Setup and Start Developing with the nRF51 DK and Keil

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, get the tools installed and get the software (SW) development environment…
- 17 Jun 2015
Debugging using QtCreator on Mac

wim

This post started as a question, but got the suggestion to post this as a blog post. Here it is. I have been trying to get QtCreator configured such that I can use it as my IDE for the nrf51822 on Mac…
- 12 Jun 2015
Trying OpenWRT Chaos Calmer (15.05 RC1) on Raspberry Pi 2

Jun Qing ZOU

| |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D…
- 11 Jun 2015
Trying OpenWRT Chaos Calmer (15.05 RC1) on Asus RT-N16

Jun Qing ZOU

| |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D…
- 11 Jun 2015
Compatibility between DFU bootloader and DFU master

Hung Bui

We have been receiving quite a few questions about the compatibility issue between the bootloaders from different SDK versions and the DFU master such as nRF Master Control Panel, nRFToolbox, etc. In…
- 10 Jun 2015