Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF93M1: plans to expose LTE Timing Advance through the AT command interface? 0

Hello Nordic Support, I am developing a cellular positioning solution using an nRF93M1 LTE Cat 1 bis module. I currently use the following command to retrieve the serving...
25 views

0 replies

Started 3 hours ago
by ing-barbiz
Not Answered
Request for RF Tuning Support – nRF54LM20 with nRF21540 FEM 0

Hi, We are experiencing a low RSSI/range issue with our nRF54LM20 module using the nRF21540 FEM. We have already consulted with you regarding the design under Case ID...
67 views

0 replies

Started 1 day ago
by Irfan Memon
Not Answered
Achieving pin retention in nRF54L15 GPIO without hardware pull-up through sys_reboot() 0

Hi, I have encountered a challenge with the nRF54L15 that I am hoping someone might know a solution for! My device has a power enable pin (on GPIO1) that must ideally...
105 views

0 replies

Started 2 days ago
by htownclyde
Not Answered
NRF_MODEM_LIB_MEM_DIAG_ALLOC Kconfig setting needs log but increments the failed allocs (which is not only used for logging statistics but for diagnosis as well). 0

I am using the SDK v3.4.0 LTS for modem error debugging I included: prj.conf I am mapping errors depending on wether memory allocations failed. I am fetching the stats...
87 views

0 replies

Started 2 days ago
by Peter Horauer
Not Answered
An aborted Channel Sounding procedure leaves ~1 mA residual current until reset (SDC 200.12506) 0

If a Channel Sounding procedure is aborted while in flight and the ACL is then disconnected, the device settles at a flat ~1 mA with the CPU asleep in the idle thread and...
111 views

0 replies

Started 3 days ago
by Nat E

Recent in the DevZone Blog

nRF5x-Tools and nRF5x-Pynrfjprog Includes Linux and Python 3 Support

gamnes

Over the last few weeks the Nordic team has been working on getting support for programming our devices in Linux as well as adding support for using our Python programming module ‘Pynrfjprog’ with Python…
- 27 Oct 2015
nRF51 DFU command line OSX app (sample)

jeremysf

OSX command line application for performing an nRF51 device firmware update: https://github.com/jeremysf/nrfDFU This is a simple command line program I wrote based on Nordic's documentation and their…
- 27 Oct 2015
Developing Nordic nRF51822 Beacon Kit Firmware with Visual Studio

ivan

This tutorial shows how to build and debug Bluetooth LE beacon firmware for the nRF51 Beacon Kit. We will use Segger J-Link together with a Tag Connect cable to debug the beacon. We will show how to use…
- 27 Oct 2015
BLEBot - a phone controlled/autonomous 2WD robot based on nRF51822

Mahesh Venkitachalam

In this project, we will build a two-wheeled robot based on the Nordic nRF51822 BLE SoC. Motor control for the two wheels of the robot will be done using an L293D chip. The robot can be controlled using…
- 12 Oct 2015
Toys 2.0: Smart Toy Robots use the nRF51 based Cannybot Brain

Wayne

The Cannybot Brain is a robotics controller board that uses the Nordic Semiconductor nRF51822 at its core. The board has been developed by Cannybots Limited in Cambridge, UK. One of Cannybots core values…
- 6 Oct 2015
Programming services, HI-LO Electronics in corporation with Nordic Semiconductor AS

HILO

In corporation with Nordic Semiconductor we are happy to announce our programming services! Your flexible programming center is based in Gothenburg, Sweden at HI-LO Electronics AB Advantages with pre…
- 30 Sep 2015