Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Editing SDK file unintentionally 0

Hello I think I have edited some SDK devicetree files unintentionally. How can I restore the default SDK files? Is there any workaround for that?
14 views

0 replies

Started 45 minutes ago
by ARHasani
Not Answered
ninja: build stopped: subcommand failed. 0

Executing task: nRF Connect: Generate config nrf52840dk/nrf52811 for ncs-fund/v2.x.x/lesson2/fund_less2_exer1 A new fatal error(s): FATAL ERROR: command exited with...
13 views

0 replies

Started 1 hour ago
by tylerca310
Not Answered
nPM1300 battery overheat shutdown forever 0

Hi, I have a situation with the nPM1300 when NTC temperature is overheat. Everything shutdown and never came back when temperature is back to normal room temperature. The...
27 views

0 replies

Started 4 hours ago
by Nguyen Hoan Hoang
Not Answered
How to confirm image installed by MCU boot 0

Hi, I still try to configure Nordic-Zepyr build for a nrf5340, with a BLE stack and MCUBoot as the bootloader. The application will receive image updates over MQTT and store...
31 views

0 replies

Started 6 hours ago
by Torsten Robitzki
Not Answered
nRF5340 Audio DK as both LE audio and BLE transfers 0

Hi, We are currently working with the nRF5340 Audio DK board and aim to implement Bluetooth Low Energy (BLE) message transmission alongside the existing LE audio transmission...
33 views

0 replies

Started 7 hours ago
by Virat

Recent in Nordic blog

Smart Hives: Beehavior Monitoring

MariaG

In the last few years, the field of IoT and especially smart home applications has seen a near exponential growth in both customizable protocols and out-of-the-box applications which everyone and their…
- 31 Aug 2021
nRF Connect for VS Code

Ali Aljaani

The nRF Connect for Visual Studio Code (VS Code) lets you develop, build, and debug applications based on the nRF Connect SDK using the VS Code Integrated Development Environment (IDE).
- 31 Aug 2021
Optimizing Power on nRF5340 SoC Designs

WesC

Objectives The objective of this blog is to guide the user in the optimization of power on the nRF5340 SoC. The goal is to understand what is needed from a software, hardware, and system level design to…
- 24 Aug 2021

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019