Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
UART configuration in a runtime 0

Hello, My board contains nRF9160 and two nRF52840. One of nRF52840 is a HCI controller (based on HCI lpuart example). nRF9160 communicates with each nRF52840 over separate...
- development
- nRF9160
- configuration
- C
- zephyr
- nrf52840
- dfu
2 views

0 replies

Started 5 minutes ago
by tdfilip
Not Answered
how to over write data in same offset into internal flash on zephyr 0

Hi, I am using the nRF Connect SDK 2.6.1 with the nRF5340 board. I referred to the soc_flash_nrf example to read and write data into flash. I need to overwrite data...
13 views

0 replies

Started 1 hour ago
by ChiragBhavsar
Not Answered
Wireshark : Encrypted packet decrypted incorrectly (bad MIC) and Empty PDU 0

Hi, I have difficulties to sniff BLE packets with nRF52840 and wireshark between a remote controller and phone. I can capture all the pairing process, I see DHKey exchange...
15 views

0 replies

Started 1 hour ago
by MalloryLP
Not Answered
Partition map migratation from ncs 2.2 -> ncs 2.7 (sysbuild) 0

Hi, I have a firmware running on ncs 2.2 with mcuboot and tfm which I'm in the process of upgrading to ncs 2.7 with sysbuild. I currently have a problem converting the...
22 views

0 replies

Started 2 hours ago
by Christoffer Brask
Not Answered
nrf52840 dk to upload code to nrf52811 0

Hi This is my first project to make my custom PCB. I have a question about how can I uploaded my code with segger embedded studio by using nrf52840 dk? For the hardware...
- development
- software
- softdevice
- nrf52840
- nRF52811
19 views

0 replies

Started 2 hours ago
by nordicDK

Recent in Nordic blog

How to get production firmware version (v1.1.0) for nRF9160

Martin Lesund

The production firmware version v1.0.0 is released for the nRF9160. - Release notes for the nRF Connect SDK v1.0.0 (NCS) - Release notes for the Modem Firmware v1.0.0 (MFW) Update NCS to v1.0.0: cd ncs…
- 12 Jul 2019
How to setup the Thread demo displayed live at Google I/O

Petter Myhre

Google I/O was wrapped up last week. One session was particularly interesting: "Connect Thread Devices to the Cloud with IoT Core". In it Google explains how the Thread protocol and their Cloud IoT Core…
- 15 May 2019
Field-testing how distance affects the behavior of LTE-M and NB-IoT

Petter Myhre

There is an updated field test at the same location from 2022. During the updated field test, we captured more parameters for both LTE-M and NB-IoT devices and, we captured power measurements of the cellular…
- 2 May 2019

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019