Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF52810 board will not start on its own. It needs the RTT Viewer to be connected, then it will start and run. 0

nRF52810 board will not start on its own. It needs the RTT Viewer to be connected, then it will start and run. It has run on its own before with this configuration: CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC...
11 views

0 replies

Started 29 minutes ago
by epolicar
Not Answered
BLE antenna switching on/off while transmitting 0

Hello, We are using a BLE module based on nRF52832 with a U.FL connector for external antenna connection. One of our automated tests requires we turn off/on the antenna...
- Evaluation
- antenna
- nrf52832
- bluetooth le
- ant
- rf design
- hardware
20 views

0 replies

Started 1 hour ago
by xinyangt
Not Answered
How to software-switch between ESB and BLE on a nrf5340 net-core? 0

Hi, I am working on a sensor device that requires very accurate timing on the sensing and sensor signal algorithm side. This device needs a low latency and low jitter radio...
22 views

0 replies

Started 4 hours ago
by nfbe
Not Answered
Emulating Xinput, what are the requirements? 0

Hello, I'm looking to get XInput working on the nRF52840 so that our device can appear as an Xbox-compatible game controller. I'd appreciate any guidance or recommendations...
- development
- software
- nrf52840
- usb
24 views

0 replies

Started 5 hours ago
by blitz0145
Not Answered
CMakePresets.json broke in new nRF Connect for VS Code version 0

Hi We are using the CMakePresets.json file for different variations of our firmware. Since the latest update (2025.4.106) the build configuration interface changed a bit...
26 views

0 replies

Started 8 hours ago
by AlanIoT

Recent in Nordic blog

Reproducible build environment for nRF52 using Rebuild (rbld.io)

Yaniv Nis

As you probably know having a build environment, you can replicate and deploy with ease has the potential to save a lot of R&D time. If you can also control its versioning so you would be able to "get…
- 31 Jul 2017
Flashing and Debugging nRF51/52 with a cheap blackmagic probe compatible SWD programmer

Mahesh Venkitachalam

When we built our Bluey nRF52 BLE dev board, we were looking for an inexpensive option for our users to upload code to bluey and debug it using ARM GDB. We then came across the blackmagic probe (BMP…
- 24 Jul 2017
Introducing nRF5 SDK for Mesh

esivertsen

The day after the Bluetooth SIG announced the 1.0 spec of the Bluetooth mesh we are happy to announce the nRF5 SDK for Mesh for our nRF51 and nRF52 Series SoCs. This first (v0.9.1) release is packed with…
- 20 Jul 2017

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019