Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
timeout occured while handling debug power 0

Hello, I am trying to flash and debug a custom board using the Raytac MDBT42Q-512KV2 that uses the nRF52832 module mounted. I tried this using the jlink plus and the nRF52...
27 views

0 replies

Started 12 hours ago
by uodami
Not Answered
Can traces be "pulled through" unused balls? 0

I have a similar question to this , however it's for the nRF54 family. Can I route similar the SWD signals out through unused pins/balls on a BGA? In this case, I'd route...
30 views

0 replies

Started 14 hours ago
by Seth_Kazarians
Not Answered
MCUBoot + CPUAPP + FLPR with BLE DFU 0

Hi DevZone, I am currently working on a project that uses MCUboot (DFU over BLE) on the CPUAPP core together with a custom FLPR application. I successfully got this working...
37 views

0 replies

Started 14 hours ago
by Notnac60
Not Answered
Custom made board on nRF9151, GPS pin back-powering VDD_GPIO 0

Hi Nordic, We are building a custom board using the nRF9151 LACA. We see a back-powering issue between the GNSS antenna bias rail and VDD_GPIO. Setup: VDD_GPIO...
- development
- auto_gps
- auto_nrf9151
- GPS
- nRF9151
- hardware
- auto_hardware
- auto_cellular_iot
41 views

0 replies

Started 17 hours ago
by Bobo0
Not Answered
Regarding FOTA failure in nRF54L15 with NSIB, MCUBoot and TF-M enabled 0

nRF54L15 FOTA Failure: MCUboot reports magic=bad on Slot 0 and magic=unset on Slot 1 using NSIB + MCUboot + TF-M with Pure DTS Partitioning Description I am implementing...
41 views

0 replies

Started 19 hours ago
by Antonysachin

Recent in the DevZone Blog

A presentation on how nRF51 DFU works

Hung Bui

Hi, I attached here some slides that we used in our technical seminar for Device Firmware Update. Download the presentation here: DFU_SDKv8.0_Pub.pdf The presentation covers: What DFU is and what…
- 4 Jun 2015
Parse MQTT message in Wireshark for IoT test

Jun Qing ZOU

Wireshark (version 1.12.5 at the time of writting) lists MQTT as supported protocol but could not parse it from the TCP payload by default. We can add some plugins to enable it. Download the Wireshark…
- 26 May 2015
Upgrade RADVD for IoT on Raspberry Pi 2

Jun Qing ZOU

The RADVD deamon in Raspberry pool is version 1.8.5 (up to Raspberry 2015-02-16). root@raspberrypi:~/radvd# apt-cache policy radvd radvd: Installed: 1:1.8.5-1 Candidate: 1:1.8.5-1 Version table…
- 25 May 2015
Workaround needed for TWI driver (nrf_drv_twi) in SDK v8.1 (TWI_COUNT missing)

Hung Bui

In SDK v8.1 we added the TWI driver (nrf_drv_twi.c). Unfortunately the nrf_drv_config.h file wasn't updated correctly with the new driver. The symptom is the error with "TWI_COUNT is missing". Here…
- 20 May 2015
Common FAQs on DFU

Hung Bui

If you are looking for a place to get started with DFU, please have a look at this presentation here and the tutorial here. In this post, we cover some in depth Q&A topics regarding Device Firmware…
- 15 May 2015
Programming the nRF51822 Beacon Kit with the nRF51DK

Stefan Birnir Sverrisson

One way to program the nRF51822 Bluetooth Smart Beacon Kit is to use the nRF51 DK. This gives you a full scale development platform (the nRF51 DK). This blog will go thru the steps needed to program…
- 7 May 2015