Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
How to determine that AWS FOTA has completed it's check, and found no update. 0

I'm working on a IoT device that leverages the AWS IoT and AWS FOTA components from the nRF Connect SDK. The device is battery powered, and so I want to limit the connection...
11 views

0 replies

Started 2 hours ago
by Jstone40649
Not Answered
NRF52840: accidental back-powering by applying voltage to GPIO pin when power is off 0

Hi there, We have a device that utilizes an NRF52840 chip. Several threads on DevZone - including this one and this one - warn about the dangers of applying voltage to a...
21 views

0 replies

Started 3 hours ago
by Steve Van Kirk
Not Answered
Can't find services using ble_db_discovery_start() 0

Using FreeRTOS and SDK 15.3 on nRF52840 and SES, SD 140 I'm following along with the NUS example project in this particular release and have a problem I'm a little stumped...
18 views

0 replies

Started 3 hours ago
by Randy Lee
Not Answered
RAK4630 power consumption in sleep mode over 900 ua 0

I'm developing firmware for a RAK4630 for IOT purposes. According to the datasheet, the average consumption of the nrf52840 is 1.5 ua in system ON mode. Mine is measuring...
19 views

0 replies

Started 4 hours ago
by Gil Madeira
Not Answered
NRF9151DK : Issue in setting LED1 : LED2 lit too 0

Hi all, I may have encountered an issue with nrf9151DK board. When I only set LED1 with dk_set_leds (DK_LED1_MSK) the LED1 and LED2 are both lit. Setting other leds...
26 views

0 replies

Started 5 hours ago
by JRSN

Recent in Nordic blog

SwiftDuino

Jason

Uses Swift Language to run your Arduino project in your App via bluetooth. https://www.facebook.com/ucxpresso.nrf/posts/1193211740761762
- 15 Dec 2016
Fast Production Screening based upon Bluetooth DTM

Ken L

The challenge As a product is getting into the production phase, the need of a fast and standalone screening facility on the production line arises. Here I'm introducing a production screening setup…
- 9 Dec 2016
I am developing an open source sensor beacon board

zelin

I am developing an open source sensor beacon board named: YS-Beacon which contains: nRF52832 DAPLink - LPC11U35 9-Axis Motion Sensor Ambient Light Sensor、Proximity Sensor and 3D-Gesture Sensor with…
- 2 Dec 2016

Latest guides

Getting started: How to add DFU support to your Thingy:91 project

Didrik Rokhaug

Note: From nRF Connect SDK v1.7.0 onwards, if you build for the thingy91_nrf9160_ns or thingy91_nrf52840, everything in this guide is already done automatically. Since that SDK release, the board files…
- 21 Jan 2021
Software: Enter the Multi-NUS: A Simple Wireless UART Network

matt.heins

If you’re thinking about building a network of sensors and you begin to survey the options, you’re likely to encounter a frothing sea of acronyms representing a variety of standards and protocols clamoring…
- 12 Jan 2021
Software and Protocols: nRF9160 DK: Offloading Bluetooth Low Energy related tasks to nRF52840 SoC

Anders Storro

Background Some time ago I was working on a project that involved communication between Bluetooth mesh and a home automation platform. The goal of this project was to enable control and observability of…
- 12 Jan 2021
Bluetooth low energy: How to update advertising data dynamically using BLE Advertising library

Karl Ylvisaker

Introduction The question of how to update advertising data dynamically using the BLE Advertising library has been raised many times by our forum-goers, especially after the release of nRF5 SDK v15.2.0…
- 6 Jan 2021
Software: Device Firmware Update (DFU) with MCUBoot bootloader

Mark Q

Purpose The purpose of this blog is to show how to create a Zephyr application that boots from the MCUBoot bootloader. We will also show how to update an application using the Device Firmware Update (DFU…
- 3 Nov 2020
Software: Building a Bluetooth application on nRF Connect SDK- Comparing and contrasting to SoftDevice based applications - Part 1

Hung Bui

Scope This is a discussion on building a Bluetooth application on our new nRF Connect SDK/Zephyr platform with the reflections to our nRF5 SDK which is based on the SoftDevice Bluetooth stack. The goal is…
- 21 Oct 2020