Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
System clock stops permanently after a GRTC compare event is lost 0

nRF54L15: system clock stops permanently after a GRTC compare event is lost Disclaimer Claude Code (Opus 5) was used to assist with this investigation and with the drafting...
12 views

0 replies

Started 29 minutes ago
by Samuel0123
Not Answered
Does single-cell location nrfcloud API work in India for Jio network? 0

Hi, We are unable to get the correct location (even approximate) using the nrfCloud API for Location based on Single-Cell. For the given "mcc", "mnc", "tac" and "eci" combination...
33 views

0 replies

Started 2 hours ago
by anupamvarghese
Not Answered
nRF9151 DK: spi slave 0

I am using the nRF9151-DK as an SPI slave . The SPI communication is not working as expected, and the nRF9151-DK is not receiving any data from the SPI master . I have configured...
- nRF9151
71 views

0 replies

Started 6 hours ago
by Aparna Pacharne
Not Answered
nRF54L15: Can Direction Finding (AoA/AoD) and Channel Sounding both work on this chip? 0

Hi, Does the nRF54L15 support Direction Finding (AoA/AoD) and Channel Sounding together — i.e., can both features run on this specific chip, either simultaneously or at...
45 views

0 replies

Started 11 hours ago
by Pravyuha
Not Answered
Is AT%XMONITOR no longer supported with the serial modem app? 0

Hi, We use the nRF9151 modem and need the following data from it: Mobile Country Code (MCC), Mobile Network Code (MNC), Tracking Area Code (TAC), cell_id and rsrp. We...
65 views

0 replies

Started 1 day ago
by Daniel B. J.

Recent in the DevZone Blog

Getting Started with the Thingy:52 and GCC/GDB

Daniel Veilleux

The Thingy:52 IoT Sensor Kit is a fancy development board that combines the nRF52832 SoC, a handful of sensors and user interface components, and a rechargeable battery. Although the Thingy is available…
- 20 Jul 2018
Provision, configure and control Bluetooth mesh networks with nRF Mesh

Petter Myhre

nRF Mesh are open source libraries for building your own Android and iOS Bluetooth mesh apps. It is also the name of the apps demonstrating a subset of the capabilities of the libraries. Use them in test…
- 25 Jun 2018
nRF52832 Buttonless DFU Development Tutorial - GitHub

gamnes

This tutorial is valid as of 2018-06-06, updates to tools and SDKs might have been made since then. Please review the information on http://infocenter.nordicsemi.com/ to see if any updates have been made…
- 12 Jun 2018
Optimizing Power on nRF52 Designs

notsane0

As customers reach the end of their design cycle, their attention generally falls on power optimization, especially for battery powered designs. The following are hints for achieving the lowest possible…
- 30 May 2018
New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018