Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
DEVKIT NPM1300 not generating VSYS 0

When I connect the two-pin battery and short pin1 and pin2 of P1, I am unable to get the battery voltage at J1 AND WHEN I LEAVE THE PINS UNSHORTED FOR P1, THEN I AM NOT GETTING...
23 views

0 replies

Started 3 hours ago
by Megha Agarwal
Not Answered
PMIC buck1 output not getting generated completely 0

I have connected the correct 47K res for VSET1 but I am not getting 1.8V, instead I am getting 2.3V I am getting the correct output for BUCK2 as 3.3V I have checked the resistor...
20 views

0 replies

Started 4 hours ago
by Megha Agarwal
Not Answered
Schematic Review Request: nRF5340 and nPM1100 bluetooth microphone 0

Hello, I am requesting a schematic review of my bluetooth microphone system. I've used the spec sheets as well as audio DK hardware reference material to design these schematics...
52 views

0 replies

Started 16 hours ago
by npwalker
Not Answered
nRF21540 DK Scanning RSSI Does Not Go Below -80 dBm with FEM (LNA) Enabled 0

Hardware: nRF21540 DK SDK Version: NCS 3.4.0 Problem Description: Modified the observer sample to scan for a specific device, using nRF21540 DK as the scanner with FEM...
96 views

0 replies

Started 5 days ago
by Bobing
Not Answered
Physical board support 0

I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
113 views

0 replies

Started 12 days ago
by DVH

Recent in the DevZone Blog

Serial Wire Debug Port Interface for nRF52832

gamnes

1.1 Description This documentation describes the use and initialization of the Serial Wire Debug Port (SWDP) interface when writing to or reading from Flash and SRAM of the nRF52832 Rev 1. See http:/…
- 2 Jun 2017
nRF52840 GATT Data Throughput with Zephyr RTOS

vich

Nordic has recently contributed support for the 2Mbit/s PHY, part of the Bluetooth 5.0 specification, to the Zephyr Project RTOS. The video below shows how to configure, build and test GATT data throughput…
- 2 Jun 2017
The complete tutorial for developing and debugging nRF52 applications on a Mac

Mohammad Afaneh

I realize that there are already multiple tutorials on how to configure GCC along with Eclipse or SEGGER Embedded Studio (for use on a Mac), but this tutorial goes over setting up a different IDE. The…
- 11 May 2017
Bluetooth 5 2Mbps Demo with nRF52 Series and Samsung Galaxy S8

John Leonard

Bluetooth 5 - now arriving in smartphones As we know, Bluetooth 5 was launched last December by the Bluetooth SIG. The nRF52 Series from Nordic have always had Bluetooth 5 and its arrival in the mix for…
- 9 May 2017
Setting up Segger on a mac or pc and debug - step by step for humans

Lola

Most guides out there are unclear and made for machines. Here is a full guide how to setup Segger for mac OS X with some example project from the SDK ( or even a PC but not tested), and also how to debug…
- 5 May 2017
FreeRTOS threads preview with J-Link, GDB/Eclipse

Radoslaw Koppel

Short note how to make FreeRTOS program debugging with eclipse little simpler. If you are looking the information how to configure the whole environment see this post: https://devzone.nordicsemi.com/tutorials…
- 11 Apr 2017