Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
WDT Callback didn`t execute when the system reset 0

Hello, I am using nRF Connect SDK v2.9.0, and nRF54l15 board. I enabled the watchdog timer and used its driver in zephyr/drivers/watchdog.h It seems to work fine. The...
5 views

0 replies

Started 22 minutes ago
by Nedaa_H_Ahmed
Not Answered
BLE Connection Issue with Multiple Simultaneous Peripherals 0

I have a BLE system where multiple sensors operate as peripherals and send data to a BLE central. These sensors enter sleep mode after transmitting data and later wake up...
11 views

0 replies

Started 59 minutes ago
by Arthur J Sary
Not Answered
How to Interface W25Q32 External Flash with nRF21540DK/nRF52840 in nRF Connect SDK 2.9.0? 0

I am using nRF Connect SDK 2.9.0 with Toolchain 2.9.0 and trying to interface Winbond W25Q32 SPI flash memory with nRF21540DK (nRF52840) . I need help with the following:...
11 views

0 replies

Started 59 minutes ago
by Dalvadi Anil
Not Answered
Optimizing Power Consumption for Battery-Operated Matter-over-Thread Device (nRF54L15) 0

Hi Nordic Team, I am planning to develop a Matter-over-Thread end device (sensor) using the nRF54L15 , which will be battery-operated . To maximize battery life (minimum...
- software
- battery
- Evaluation
- nRF54L15
- thread
13 views

0 replies

Started 59 minutes ago
by Bhavya Mathukiya
Not Answered
Problem with GNSS - delay in detecting satellites 0

Hello, i'm having a problem with the satellite detection time when I start gnss search. When I start the search, for a while at first the satellites are not detected and then...
24 views

0 replies

Started 1 hour ago
by GoncaloS

Recent in Nordic blog

Programming nRF51 with ST-Link & uVision

Milan

Hi, I am planning to design a device based on nRF51-dk but with external programmer. I have ST-Link available so I thought I just provide a simple walk through showing how to set it up. Firstly, here…
- 10 Dec 2014
Visualising your memory usage

Eliot Stock

The linker in the GCC toolchain, ld, produces a *.Map file which shows you how the memory on your micro is being used. This file is a goldmine of information but it's a bit difficult for humans to absorb…
- 2 Dec 2014
Using the ADC with the S110 SoftDevice

Stefan Birnir Sverrisson

A good place to start with getting to know how to use the ADC with the S110 SoftDevice is by using one of the BLE ADC code examples provided on Nordic's Github page, where BLE examples have the "ble_…
- 28 Nov 2014

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019