Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
When connecting to AWS IoT with low signal it gets stuck 0

We have devices that have low signal so they have to reconnect to AWS a lot. We have a watchdog timer with a 100s timeout that we feed every 10 seconds in the control loop...
5 views

0 replies

Started 7 minutes ago
by charleshaf
Not Answered
With nrf5_sdk_1.7.1, the BLE_APP_UART example will get stuck 0

bool erase_bonds; // Initialize. uart_init(); log_init(); timers_init(); //buttons_leds_init(&erase_bonds); // power_management_init(); ble_stack_init(); gap_params_init...
3 views

0 replies

Started 14 minutes ago
by shsh
Not Answered
the file: thingy53_nrf5340_cpuapp.conf in v2.6.0/bootloader/mcuboot/boot/zephyr/boards 0

Hi Community, I made a custom board based on thingy53, created a similar custom board file folder. The application code can be compiled correctly with the original thingy53...
25 views

0 replies

Started 12 hours ago
by danny0007
Not Answered
QSPI initialization error sdk v2.6.1 0

Hello I am trying to initialize qspi in a ".cpp" file and methods like PINCTRL_DT_DEFINE ( QSPI_NODE ); are giving me "out-of-order initializers are nonstandard in C...
27 views

0 replies

Started 13 hours ago
by kalbani
Not Answered
Put the BLE block in sleep to reduce consumption in a nRF52832 using Softdevice 0

Hello, In a project using the NRF52832. Softdevice SDK 19.1.0 and Segger IDE, I inizialize the BLE for having NUS and DFU services actives. I try to reproduce the code here...
23 views

0 replies

Started 15 hours ago
by jinvers

Recent in Nordic blog

On nRF Connect for iOS and its Unnecessary BitField Collection in Swift

Dinesh Harjani

For the longest time we’ve had this idea, of turning one of our most-used Swift Collection Types into a simple one-instruction comparison call, down at the assembly level, to check whether an element belongs…
- 23 Jul 2020
Measuring PSM Sleep Current on the nRF9160-DK

notsane0

Overview In this blog, you will measure the PSM floor current for the rev. 2 version of the nRF9160 SiP. Requirements Hardware You will need: an nRF9160-DK (the one used here was v1.0.0). Be sure that…
- 7 May 2020
Developing for the nRF52820 with nRF5 SDK v16.0.0

bjorn-spockeli

Please note that this blogpost is now deprecated as the nRF52820 is fully supported in nRF5 SDK v17.0.0. We recommend using SDK v17.0.0 for nRF52820 fimware development. Introduction The nRF52820 IC is…
- 19 Mar 2020

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019