Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF54L15 Radio Event ISR 0

Good Morning, I'm currently developing an application for the nRF54L15 where I only need to send single BLE packages, therefore arising the need for keeping track of the...
- development
- event
- software
- nRF54L15
- bluetooth le
0 views

0 replies

Started a few seconds ago
by lahn
Not Answered
Configuration on b0n image to read the Network Core version on SDK v2.9.0 0

Hey! I am working on a project that requires downgrade prevention of the Network Core and also requires the application core to read the Network Core version, set with the...
16 views

0 replies

Started 56 minutes ago
by Esnoar@CicloSport
Not Answered
NRF PPK2 can't to show the correct current compare with my old one 0

Today I bought a new NRF-PPK2, but compare with my old NRF-PPK2. For the old and new PPK2, I use the same DUT. It can't show the same current with my old one? can you...
13 views

0 replies

Started 1 hour ago
by Markhu123
Not Answered
nRF54L15 matching antenna inverted f.remove matching network component 0

Currently nRF54L15 is being matched with LOW Q circuit and unipolar antenna. Because low Q circuit takes a lot of components and time when designing hardware. So I can remove...
- antenna
- nRF54L15
- hardware
- production
22 views

0 replies

Started 2 hours ago
by sangbg98
Not Answered
Battery Measurement 0

Hi,Team, I'm using nrf54l15-dk. I want to read the battery level, which routine should I refer to? My ncs version is v2.8.0. Thanks.
16 views

0 replies

Started 4 hours ago
by dede

Recent in Nordic blog

nrF52 Tutorial: ETM Instruction Trace with Keil MDK

Bob Boys

Hello I wrote a tutorial on using the nrF52 Development Kit with Keil MDK. www.keil.com/appnotes/docs/apnt_308.asp This document features essential debugging capabilities of the nrF52 series. ETM Instruction…
- 15 Dec 2017
One minute to understand BLE connection data package

viewtool

1.Profile During connection procedure of BLE, there are three packages: SCAN_REQ, SCAN_RSP 和 CONNECT_REQ。 SCAN_REQ： Scan request, issued by MASTER DEVICE, send to SLAVE DEVICE，sent by the Link Layer…
- 15 Dec 2017
One minute to understand BLE MTU data package

viewtool

1.Profile MTU: ATT Maximum Transmission Unit (MTU) is the maximum length of an ATT packet. The ATT MTU is defined by the L2CAP and can be anywhere between 23 and infinity. The implementation of the Bluetooth…
- 15 Dec 2017

Latest guides

Getting Started: Developing for the nRF52805 with nRF5 SDK

bjorn-spockeli

Introduction The nRF52805 SoC is a low-cost member of the nRF52 Series with a subset of the features of the nRF52811 and nRF52810 SoCs. As the nRF52805 has a feature subset of the nRF52810/11 SoCs, which…
- 11 Jun 2020
nRF5x: nRF52832 Specific PCB Guidelines

Andreas

This guide will cover the specific areas that must be paid extra attention to when designing a PCB for nRF52832. It is intended as a nRF52832 specific addition to the General PCB design guidelines for…
- 10 Jun 2020
Hardware design, RF test and coverage: iBasis eSIM International Coverage Update

Brian Kim

Since Nordic Semiconductor announced that it has partnered with one of the world’s largest international cellular carriers, iBASIS, to use nRF9160 System-in-Package (SiP) module and to include an iBasis…
- 4 Jun 2020
Getting started: Getting NB-IoT Demo running on Thingy:91

Christian Kurz

The Nordic Thingy:91 is a cellular IoT prototyping platform. It is based on the nRF9160 System-in-Package (SiP). The nRF9160 has an integrated modem that supports both LTE-M and NB-IoT. The factory programmed…
- 29 May 2020
Bluetooth low energy: Mocking CoreBluetooth

Aleksander Nowakowski

CoreBluetooth is the native iOS framework to communicate with Bluetooth-enabled Low Power (LE) devices, except iBeacons (which require CoreLocation) and HomeKit devices. It is easy to start with, if one…
- 9 Mar 2020
Getting Started : Build NCS application firmware images using Docker

Markus Tacker (he/him)

How to compile a NCS application using Docker so you don't need to install dependencies directly in your system.
- 17 Feb 2020