Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
PWM issue on nR54L15F-PDK 0

nRF Connect SDK Intermediate , Lesson 4, Exercise 1: I tried to build solution ( https://github.com/NordicDeveloperAcademy/ncs-inter/tree/main/v2.9.0-v2.7.0/l4/l4_e1_sol...
- pwm
- software
- Evaluation
- nRF54L15
- zephyr
5 views

0 replies

Started 5 minutes ago
by Igor
Not Answered
DECT NR+: How to configure the Physical Layer Control Field Type 2 Header 0

Hey, I’m currently evaluating DECT NR+ using two nRF9151 DKs with the nRF Connect SDK v2.9.0. According to the ETSI specification (ETSI TS 103 636-4 V2.1.1), the Physical...
9 views

0 replies

Started 46 minutes ago
by Luca12
Not Answered
nRF54L15-CAAA WLCSP Light Sensitivity and Underfill Requirements 0

I am working with the WLCSP version part (nRF54L15-CAAA) and it calls out that there is light sensitivity. The note seems to indicate that only underfill around the perimeter...
12 views

0 replies

Started 47 minutes ago
by AntonioFCDS
Not Answered
No Serial Output When Flashing Matter Application to nRF54L15 Internal Flash 0

Hello Nordic Team, I'm experiencing issues when trying to flash my Matter application to the internal flash of the nRF54L15. I've followed the guidance from this forum post...
14 views

0 replies

Started 1 hour ago
by xiongwei.wang
Not Answered
How to get status of message transmission 0

My application communicates via UDP and all communication is initiated from the device. Before packet transmission, network registration status is checked (CEREG) and sendto...
- development
- software
- nRF9160
- nb-iot
- low-power
15 views

0 replies

Started 2 hours ago
by Martin Vitek

Recent in Nordic blog

Flashing nRF5x firmware using any dumb terminal program via standard serial COM port

Nguyen Hoan Hoang

There are times that we needed to flash the nRF5x series on a PC where the development software were not installed. The problem could be worst when network access is limited. With a HEX file on hand…
- 18 Sep 2017
How to Debug the nRF52 Interrupts — Useful Tips

Yaniv Nis

Debugging interrupts in not an easy task. During the development of Jumper's Emulator, we gather few useful tips that we think can help you all when debugging the nRF52 interrupts. Hope it will help…
- 13 Sep 2017
The ultimate guide to maximizing your BLE and Bluetooth 5 data throughput

Mohammad Afaneh

In my 2nd blog post in the series on Bluetooth 5, I go over one of the main features of Bluetooth 5: 2x speed. The advertised 2x speed of Bluetooth 5 is great! BUT, what does that even mean? Is it…
- 7 Sep 2017

Latest guides

Getting Started: Developing for the nRF52805 with nRF5 SDK

bjorn-spockeli

Introduction The nRF52805 SoC is a low-cost member of the nRF52 Series with a subset of the features of the nRF52811 and nRF52810 SoCs. As the nRF52805 has a feature subset of the nRF52810/11 SoCs, which…
- 11 Jun 2020
nRF5x: nRF52832 Specific PCB Guidelines

Andreas

This guide will cover the specific areas that must be paid extra attention to when designing a PCB for nRF52832. It is intended as a nRF52832 specific addition to the General PCB design guidelines for…
- 10 Jun 2020
Hardware design, RF test and coverage: iBasis eSIM International Coverage Update

Brian Kim

Since Nordic Semiconductor announced that it has partnered with one of the world’s largest international cellular carriers, iBASIS, to use nRF9160 System-in-Package (SiP) module and to include an iBasis…
- 4 Jun 2020
Getting started: Getting NB-IoT Demo running on Thingy:91

Christian Kurz

The Nordic Thingy:91 is a cellular IoT prototyping platform. It is based on the nRF9160 System-in-Package (SiP). The nRF9160 has an integrated modem that supports both LTE-M and NB-IoT. The factory programmed…
- 29 May 2020
Bluetooth low energy: Mocking CoreBluetooth

Aleksander Nowakowski

CoreBluetooth is the native iOS framework to communicate with Bluetooth-enabled Low Power (LE) devices, except iBeacons (which require CoreLocation) and HomeKit devices. It is easy to start with, if one…
- 9 Mar 2020
Getting Started : Build NCS application firmware images using Docker

Markus Tacker (he/him)

How to compile a NCS application using Docker so you don't need to install dependencies directly in your system.
- 17 Feb 2020