Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Setting Non-Connectable and Scannable Extended Advertising in NCS v2.5.0 (nRF52840) 0

Hi， When I use NCS V2.5.0 （board：nRF 52840），I want to set the Non-Connectable and Scannable Extended Advertising.My code as follows.I use the APP nRF Connect for moblie...
25 views

0 replies

Started 4 hours ago
by qianjunwang
Not Answered
Factory Data OTA 0

Hi Nordic team. I'm finding a way to update the factory data over-the-air. Specifically, I want to update the Matter Certification information (PAI, DAC, ...) over-the-air...
33 views

0 replies

Started 9 hours ago
by DungDA
Not Answered
Can I set ADV_EXT_IND without AUX packet？ 0

Hi， In Core Specification v5.4, there is support for Non-Connectable and Non-Scannable Extended Advertising (ADV_EXT_IND) without AUX packets. However, when using Nordic...
30 views

0 replies

Started 10 hours ago
by qianjunwang
Not Answered
Having multiple network interfaces up at once? 0

When both ethernet and WiFi are supported on one MCU (with both sharing the same L2 implementation, only one network device being active at a time), does it matter if both...
30 views

0 replies

Started 12 hours ago
by Amira R.
Not Answered
nRF9160 GNSS periodic mode, every once in a while GNSS will not enter sleep after a fix 0

we have a custom board with nRF9160, when using GNSS we configured it to periodic mode with 120 second interval, most time it works fine but every once in a while (like every...
29 views

0 replies

Started 16 hours ago
by yyang3

Recent in Nordic blog

Flashing nRF5x firmware using any dumb terminal program via standard serial COM port

Nguyen Hoan Hoang

There are times that we needed to flash the nRF5x series on a PC where the development software were not installed. The problem could be worst when network access is limited. With a HEX file on hand…
- 18 Sep 2017
How to Debug the nRF52 Interrupts — Useful Tips

Yaniv Nis

Debugging interrupts in not an easy task. During the development of Jumper's Emulator, we gather few useful tips that we think can help you all when debugging the nRF52 interrupts. Hope it will help…
- 13 Sep 2017
The ultimate guide to maximizing your BLE and Bluetooth 5 data throughput

Mohammad Afaneh

In my 2nd blog post in the series on Bluetooth 5, I go over one of the main features of Bluetooth 5: 2x speed. The advertised 2x speed of Bluetooth 5 is great! BUT, what does that even mean? Is it…
- 7 Sep 2017

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019