Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Assistance Needed: Power Profiler II Connection and Mode Selection for PCBA Testing 0

Dear Team, We want to use the Power Profiler II as our ammeter to measure the current of our newly designed PCBA. However, we’re uncertain about the proper connections for...
3 views

0 replies

Started 16 minutes ago
by Viknesh
Not Answered
Can not run nomally when setting CONFIG_BT_BONDABLE 0

I am running demo nrf/samples/matter/lock. I tried to use CHIP_NUS so I set CONFIG_CHIP_NUS =y, it worked well. After that, I wanted to make it bondable so I set CONFIG_BT_BONDABLE...
5 views

0 replies

Started 22 minutes ago
by Llama12580
Not Answered
How to Enable/Disable the CC312 Accelerator on nRF5340 for Encryption 0

I am planning to perform encryption using the CC312 accelerator on the nRF5340. I would like to evaluate the power consumption when using the accelerator. My approach is...
5 views

0 replies

Started 49 minutes ago
by giun.kim
Not Answered
NPM1300 ferrite on NTC signal 0

Hello, We are using the npm1300 with a battery with an NTC. Can we add a ferrite between battery NTC and npm1300 NTC? Note: there is an error in our design we will...
10 views

0 replies

Started 1 hour ago
by tcube
Not Answered
nrf5340 SPI 32MHz, HFCLK128M 128MHz and QSPI usage 0

Hello, We have a Nor flash connected to the QSPI and another peripheral connected to the classic SPI. Due to the errata [159] , the HFCLK128M is running at 64MHz and...
11 views

0 replies

Started 1 hour ago
by tcube

Recent in Nordic blog

New Command Line Interface and enhanced Logger - part 2.

Krzysztof Chruscinski

If you haven't yet get to know command line interface (nrf_cli) module significantly improved in nRF5 SDK 14.0.0 please check this blog post: New command line interface - part 1 Enhanced logger and…
- 22 Aug 2017
MultiLink with Peripherals & Centrals in the nRF5 SDK v13

JustinLee

##Introducing concurrent MultiLinks I’d like to inform that it is possible to configure concurrent-multiple connections with several Centrals and Peripherals. This behavior can be possible to use examples…
- 22 Aug 2017
Nordic Thingy:52 Raspberry Pi Python Interface

gamnes

Thingy:52 Python Raspberry Pi Interface This blog is a follow up to both the Nordic Thingy:52 node.js/Raspberry Pi demos and the https://devzone.nordicsemi.com/blogs/1160/walkthrough-of-nordic-thingy52…
- 18 Aug 2017

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019