Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Server certificate expiry time is not verified 0

Dear support, We are connecting with an MQTT server with an expired server certificate. My expectation is that the handshake fails, but apparently the NRF9161 accepts the...
3 views

0 replies

Started 4 minutes ago
by Joost Raats
Not Answered
Inquiry regarding NCSDK-38697: Unexpected DFU behavior when migrating from Partition Manager to Devicetree (NCS v3.2.4 to v3.3.1) 0

Hello. We are developing a project based on the nRF54L15 SoC, utilizing MCUboot, image compression, and TF-M (Trusted Firmware-M). As part of our upgrade from NCS v3.2.4...
7 views

0 replies

Started 18 minutes ago
by a.da
Not Answered
nRF54H20 SPIS read delayed after switching to new partitioning (aligned with single-slot DFU) even without MCUboot enabled 0

Hi Nordic team, I have an issue with SPI slave timing on nRF54H20 after I change to a new partitioning scheme that mimics the single-slot DFU / merged-slot layout, even...
19 views

0 replies

Started 1 hour ago
by lammobile
Not Answered
Measure current via VBUSIN on the nPM1300 during end-of-line-test 0

Hello support! I am using the nRF9151 and the nPM1300 on a custom board. Is is possible to measure the current drawn by the board via the VBUSIN? The reason is too have...
22 views

0 replies

Started 4 hours ago
by olofjohnsson
Not Answered
Both Conexa and Onomondo SIM card don't work in NRF9151 0

I am doing Dev Academy course for the Cellular IoT using the NRF9151-DK. I was able to follow the tutorial to the point where I was able to claim the device using a token...
43 views

0 replies

Started 14 hours ago
by Ola Oni

Recent in the DevZone Blog

Developing Nordic nRF51 applications with mbed and Visual Studio

ivan

This tutorial shows how to use the mbed framework to develop applications for Nordic nRF51 devices. Before you begin, install VisualGDB 5.1 or later. Start Visual Studio and open the VisualGDB Embedded…
- 26 Jan 2016
PA / LNA support in S132

Einar Thorsrud

The S132 SoftDevice for the nRF52 has support for enable/disable switching of external Power Amplifiers (PA) and Low Noise Amplifiers (LNA) using GPIO pins. This was introduced in S132 version 2.0.0-7…
- 25 Jan 2016
Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016
An introduction to error handling in nRF5 projects

Audun

As you start developing with the nRF5 series chips, SoftDevices, and SDKs, it's very useful to learn how errors can be discovered (and preferrably recovered from). This can be detecting something as simple…
- 20 Jan 2016