Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Porting nRF7002 WiFi driver to another platforms 0

I am working on RTOS that does not have WiFi driver for nordic wifi chips. I would like to port this driver to that RTOS. In the documentation there is a mention of platform...
- development
- software
- Wi-Fi
- nRF7002
0 views

0 replies

Started 2 minutes ago
by ujur007
Not Answered
Evaluating Protocol for Smart Lighting System 0

Hi, I’m exploring the use of the Thread/Matter protocol for a smart lighting system. My goal is to have the system communicate seamlessly with the cloud—allowing commands...
- software
- beginner
- nRF Connect SDK
- Evaluation
- mesh
- thread
- LED Lighting
- nRF5340
0 views

0 replies

Started 14 minutes ago
by chunjie
Not Answered
GATT CONN TIMEOUT in nrf connect for mobile application. 0

Hi, I'm trying to do DFU on a custom designed Bluetooth peripheral device using nrf connect for mobile application. I can able to perform DFU successfully is some mobile...
4 views

0 replies

Started 37 minutes ago
by Nabeel Ar
Not Answered
Add mcuboot to hello_world sample does not work in SDK 2.8.0 0

Hi, I started my project with SDK version 2.6.1 (starting from the 'hello_world' example). I added mcuboot (CONFIG_BOOTLOADER_MCUBOOT=y). I followed the instructions in the...
8 views

0 replies

Started 1 hour ago
by derWabe
Not Answered
Questions: External Flash required for Matter? 0

Hello. I am trying to use nRF Connect SDK v2.8.0 and nRF52840 to run Matter's Light Switch and Light Bulb. I was able to confirm that it works with nRF52840-DK, but...
21 views

0 replies

Started 6 hours ago
by Kenta

Recent in Nordic blog

nRF52840 GATT Data Throughput with Zephyr RTOS

vich

Nordic has recently contributed support for the 2Mbit/s PHY, part of the Bluetooth 5.0 specification, to the Zephyr Project RTOS. The video below shows how to configure, build and test GATT data throughput…
- 2 Jun 2017
The complete tutorial for developing and debugging nRF52 applications on a Mac

Mohammad Afaneh

I realize that there are already multiple tutorials on how to configure GCC along with Eclipse or SEGGER Embedded Studio (for use on a Mac), but this tutorial goes over setting up a different IDE. The…
- 11 May 2017
Bluetooth 5 2Mbps Demo with nRF52 Series and Samsung Galaxy S8

John Leonard

Bluetooth 5 - now arriving in smartphones As we know, Bluetooth 5 was launched last December by the Bluetooth SIG. The nRF52 Series from Nordic have always had Bluetooth 5 and its arrival in the mix for…
- 9 May 2017

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019