Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Adding a nRF24L01 to a breadboard or stripboard 0

I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
- breadboard
- nrf24l01
1495 views

0 replies

Started over 9 years ago
by Neil Kolban
Not Answered
nRF51822 books, documentation 0

Hello. Can I get a literature to the nRF51 series? I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
- bluetooth low energy
- nrf51822
878 views

0 replies

Started over 9 years ago
by HAKMUN
Not Answered
some connect problem when use hts . 0

hts, HTC phone, nrf tools HTM, nrf51822, every time when it's power up : the once connect: error code 0x7A cann't read characteristic and 0x14 state change. the second...
- hts err manual
704 views

0 replies

Started over 9 years ago
by Liu
Not Answered
4 channel wireless transceiver and 4 RF temperature sensors as a finished product set: 0

Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
- any fcc approved
1062 views

0 replies

Started over 9 years ago
by baha93
Not Answered
How to get Value of multilink_peripheral on terminal, that is displayed on Mastrer Control panel 0

I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
- value
- mcp
- dongle
- lave
- terminal
631 views

0 replies

Started over 9 years ago
by Mohib

Recent in Nordic blog

Serial Wire Debug Port Interface for nRF52832

gamnes

1.1 Description This documentation describes the use and initialization of the Serial Wire Debug Port (SWDP) interface when writing to or reading from Flash and SRAM of the nRF52832 Rev 1. See http:/…
- 2 Jun 2017
nRF52840 GATT Data Throughput with Zephyr RTOS

vich

Nordic has recently contributed support for the 2Mbit/s PHY, part of the Bluetooth 5.0 specification, to the Zephyr Project RTOS. The video below shows how to configure, build and test GATT data throughput…
- 2 Jun 2017
The complete tutorial for developing and debugging nRF52 applications on a Mac

Mohammad Afaneh

I realize that there are already multiple tutorials on how to configure GCC along with Eclipse or SEGGER Embedded Studio (for use on a Mac), but this tutorial goes over setting up a different IDE. The…
- 11 May 2017

Latest guides

Software and Protocols: How to connect nRF9160 DK to Google Cloud

Marte Myrvold

This project was originally made in an outdated version of NCS, but it has now been updated to NCS v1.5.0. The instructions are the same as before, but the code is different. Disclaimer: This is a student…
- 17 Jul 2019
Mesh Networks: Automating Nordic BLE Mesh Provisioning

Mark Q

Purpose This document will show how to automate the provisioning process for Nordic BLE Mesh nodes using Python scripting. When provisioning nodes using PyACI (Python Application Controller Interface)…
- 8 Jul 2019
Bluetooth low energy: MIDI over Bluetooth LE

Håvard

I implemented parts of the BLE-MIDI service along with a small example application. I wanted to share it here on the blog, in case someone would find it useful. The intended audience is primarily someone…
- 30 Jun 2019
Mesh Networks: Thread Tutorial: Practical guide for device upgrade OTA

AndreasF

This getting started guide is meant as a more detailed practical guide for the Thread Secure DFU Example found on Infocenter which demonstrates upgrade of firmware over the air (OTA). For any questions…
- 7 Jun 2019
Mesh Networks: Zigbee Tutorial: Practical guide for device upgrade OTA

AndreasF

This getting started guide is meant as a more detailed practical guide for the Zigbee OTA (Over the Air) Upgrade Client Example found on Infocenter. If you have any questions regarding Zigbee or Zigbee…
- 27 May 2019
Getting Started : nRF Connect SDK Tutorial series - Part 0 | NCS v1.5.0

Simon

This tutorial uses an outdated version of nRF Connect SDK. We recommend using the latest version of nRF Connect SDK when getting started with development. Please see academy…
- 24 May 2019