Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
RedBear Blend Micro use pairing passkey 0

Hi, I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device. Is it possible? Static passkey...
- ble blend passkey io
756 views

0 replies

Started over 10 years ago
by isi
Not Answered
How to interface multiple RF transmitters with single RF reciever? 0

How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ? I am working on a polling system. This one is similar to the audience...
- 433mhz
2341 views

0 replies

Started over 10 years ago
by Ajinkya
Not Answered
Writing peripheral characteristic value 0

Hello, I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
- value
- bluetooth low energy
- keil
- write
- nrf51822
- characteristic
2612 views

0 replies

Started over 10 years ago
by nejcokle
Not Answered

NRF24L01 Breakout boards 0

I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...

796 views

0 replies

Started over 10 years ago
by THLL
Not Answered

Nrf905 packets and CRC check methods 0

Hi, my friend, I've been with nrf905. I use a 16-bit CRC check. But I encountered problems in use: 1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...

991 views

0 replies

Started over 10 years ago
by Jesen

Recent in Nordic blog

Writing BLE firmware with a few lines of code

Nguyen Hoan Hoang

Writing a BLE firmware can now be done with a few lines of code. The code example bellow is all you need to write for a non-connectable BLE firmware that advertise a counter value every second in the…
- 29 Dec 2017
nrF52 Tutorial: ETM Instruction Trace with Keil MDK

Bob Boys

Hello I wrote a tutorial on using the nrF52 Development Kit with Keil MDK. www.keil.com/appnotes/docs/apnt_308.asp This document features essential debugging capabilities of the nrF52 series. ETM Instruction…
- 15 Dec 2017
One minute to understand BLE connection data package

viewtool

1.Profile During connection procedure of BLE, there are three packages: SCAN_REQ, SCAN_RSP 和 CONNECT_REQ。 SCAN_REQ： Scan request, issued by MASTER DEVICE, send to SLAVE DEVICE，sent by the Link Layer…
- 15 Dec 2017
One minute to understand BLE MTU data package

viewtool

1.Profile MTU: ATT Maximum Transmission Unit (MTU) is the maximum length of an ATT packet. The ATT MTU is defined by the L2CAP and can be anywhere between 23 and infinity. The implementation of the Bluetooth…
- 15 Dec 2017
Debugging on nrf52840 with GDB from CLI on linux

jfcamel

Today I tried to find the better ways to debug program on nRF52840 PDK from CLI on linux. The ways that I tried [Failed] openocd (both stlink and jlink) & gdb [Succeeded] JLink & JLinkGDBServer &…
- 14 Dec 2017
The KEY POINT of example "ble_app_uart"

QQ645116977

This article baed on "pca10040", nRF52832 example code path "examples/ble_peripheral/ble_app_uart" IMPORTANT!!!! board config file of this example located in "components/boards/pca10040.h" and uart…
- 12 Dec 2017