Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
MPU6000 SPI 0

Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
- nrf42522
- mpu6000 accelerometer spi
1337 views

0 replies

Started over 10 years ago
by Josue
Not Answered
nRF51 Bluetooth Smart GATT/GAP Driver for Linux ARM? 0

I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
- nrf51822 embedded linux
522 views

0 replies

Started over 10 years ago
by Erik Sanchez
Not Answered

Bike Power Meter service on S310 0

Are there plans to add the Bike Power Meter service to the S310 SoftDevice?

812 views

0 replies

Started over 10 years ago
by Oct
Not Answered
External clock reference and SoftDevice stack compatibility 0

It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
800 views

0 replies

Started over 10 years ago
by Hynek
Not Answered

information for cc2500 and nRF24L01+ 0

Hello, between these two modules cc2500 and nRF24L01+ can be communicate ?? are compatible? Thanks

732 views

0 replies

Started over 10 years ago
by sgarrupino84

Recent in Nordic blog

Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015
An appeal to makers - why you should document your project, and how you can do it

Mahesh Venkitachalam

An appeal to makers - why you should document your project, and how you can do it. http://electronut.in/why-how-document-project/
- 3 Aug 2015

Latest guides

nRF5x: Current measurement guide: Introduction

Stian Røed Hafskjold

###Other relevant posts A concise guide to equipment setup, and how to use the development kit for current measurements can be found here: Measuring current with PCA10040 v0.9.0 A post that describes…
- 1 Dec 2015
nRF5x: General PCB design guidelines for nRF51 series

Petter Myhre

When designing a PCB with nRF51, nRF51822 or nRF51422, there are some rules that should be followed in order to get a good working radio/system, with a maximized range. General rule The RF part of the…
- 13 Nov 2015
Software Development Kit: nRF5 SDK Scheduler Tutorial

Einar Thorsrud

2019-02-08: Updated tutorial to cover nRF5 SDK version 15.2. Introduction Scope The following topics will be included in this tutorial: Configuration of the Scheduler library. Using the scheduler with…
- 9 Nov 2015
Bluetooth low energy: Bluetooth low energy central tutorial

Anders Strand

Scope Topics that will be covered include: Before we begin Necessary equipment and software Necessary prior knowledge Setting up the example projects Background theory Central and peripheral roles…
- 4 Nov 2015
Software Development Kit: nRF5 SDK Application Timer Tutorial

Einar Thorsrud

2018-11-23: Updated tutorial to cover SDK version 15.2. 2019-02-08: Improved example project (SDK 15.2) and updated instructions accordingly. Introduction Scope The following topics will be included in…
- 30 Oct 2015
Bluetooth low energy: Bluetooth low energy Services, a beginner's tutorial

MartinBL

Before we begin Scope Topics that will be covered include: Before we begin Necessary equipment and software Necessary prior knowledge Some basic theory The Generic Attribute Profile (GATT) Services…
- 26 Aug 2015