Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Questions about BLE-Optiboot 0

Hi everyone, I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...

618 views

0 replies

Started over 10 years ago
by Petter M.
Not Answered
Need help getting started on a beacon project 0

I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need. I'm looking...
- nrf51822
579 views

0 replies

Started over 10 years ago
by J3RMz
Not Answered
Write Cycle ? 0

Hello , I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
- nrf24l01+ hardware reset
606 views

0 replies

Started over 10 years ago
by Burak Günay
Not Answered
NRF51822 as server role 0

Hi, This post is very old. devzone.nordicsemi.com/.../ I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
1116 views

0 replies

Started over 10 years ago
by mobi
Not Answered
NRF24L01 No range 0

Hello! I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS. In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
- nrf24l01
904 views

0 replies

Started over 10 years ago
by E.Junior

Recent in Nordic blog

Programming the nRF51822 Beacon Kit with the nRF51DK

Stefan Birnir Sverrisson

One way to program the nRF51822 Bluetooth Smart Beacon Kit is to use the nRF51 DK. This gives you a full scale development platform (the nRF51 DK). This blog will go thru the steps needed to program…
- 7 May 2015
Bluz, a cloud connected Bluetooth LE development kit based on the nRF51822, is live on Kickstarter

eric ely

Bluz is a brand new development kit that brings Bluetooth LE to the internet. We have paired up with Spark and ported their FW to the nrf51822, allowing Bluz to be controlled and programmed over the…
- 15 Apr 2015
nRF51 current consumption for common scenarios

Stefan Birnir Sverrisson

The following is the estimated nRF51 current consumption during advertising with the DCDC disabled. Advertising 1: TX power: +4dBm adv interval: 20ms (minimum advertising interval in normal adversising…
- 14 Apr 2015
Building kernel for RPi2 with bluetooth_6lowpan for Raspbian

Håkon Alseth

Building kernel for RPi2 with bluetooth_6lowpan In this guide, you will have two choices: Cross-compilation build Native build Choose the one that fits your needs. Cross-compilation is…
- 9 Apr 2015
Debugging with Real Time Terminal

FormerMember

In SDK 12.0.0 or later, logging/debugging over RTT is built in to the logger module NRF_LOG. To enable logging over RTT, "check" the NRF_LOG_BACKEND_SERIAL_USES_RTT option in sdk_config.h in the configuration…
- 8 Apr 2015
Accessing the BLE mesh via the particle.io (spark.io) cloud

David Edwin

Hello. I was spending the last few days to implement an interface to access the BLE mesh via the Internet. The mesh consists of devices with LEDs, which then could be turned on and off in my browser.…
- 1 Apr 2015