Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Using lib_aci_connect vs. lib_aci_broadcast 0

I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
- nrf8001
512 views

0 replies

Started over 9 years ago
by Mahesh Venkitachalam
Not Answered
printf with redbearlab nrf51822 board 0

Hi, I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
- retarget.c printf
- printf
1110 views

0 replies

Started over 9 years ago
by RTR
Not Answered
How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiver? 0

An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
- nrf51822 pa lna s110 ble
2422 views

0 replies

Started over 9 years ago
by cenuser
Not Answered

SDK 8.1.0 example 0

Hi... Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...

520 views

0 replies

Started over 9 years ago
by sruthiraj koodathil
Not Answered
Setting ACI connect/bond/broadcast parameters in nRFgo 0

I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer. ...
- nrf8001
913 views

0 replies

Started over 9 years ago
by Mahesh Venkitachalam

Recent in Nordic blog

SD card interfacing

Salman

Hi, I have written SD & SDHC card routine for reading, writing and erasing data from SD card. It used the hardware SPI of nRF51822. NOTE: 1)Define the PINs of SD card first before initialing. 2)Define…
- 10 Oct 2014
How different BLE packet types influence throughput

Stefan Birnir Sverrisson

There are several types of write operations, write request with authorization, write request without authorization and write command. You can see message sequence charts for those messages here and he…
- 9 Oct 2014
Measuring Lithium battery voltage with nRF51

Stefan Birnir Sverrisson

Here is an example of a hardware setup to measure the voltage on a Lithium battery with a voltage divider and a connected capacitor. The Lithium battery typically has a voltage range of 2.7 - 4.2 V and…
- 2 Oct 2014

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019