Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Questions about BLE-Optiboot 0

Hi everyone, I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...

596 views

0 replies

Started over 10 years ago
by Petter M.
Not Answered
Need help getting started on a beacon project 0

I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need. I'm looking...
- nrf51822
558 views

0 replies

Started over 10 years ago
by J3RMz
Not Answered
Write Cycle ? 0

Hello , I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
- nrf24l01+ hardware reset
579 views

0 replies

Started over 10 years ago
by Burak Günay
Not Answered
NRF51822 as server role 0

Hi, This post is very old. devzone.nordicsemi.com/.../ I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
1081 views

0 replies

Started over 10 years ago
by mobi
Not Answered
NRF24L01 No range 0

Hello! I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS. In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
- nrf24l01
873 views

0 replies

Started over 10 years ago
by E.Junior

Recent in Nordic blog

Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016

Latest guides

Software: Using nRF Connect SDK and west to compile and program the DTM example into the nRF52840 DK

Jay Tyzzer

Background There is a need to enable Nordic hardware with the Direct Test Mode (DTM) firmware. This is so the physical layer and RF characteristics may be ascertained as set in the Bluetooth Sig Specification…
- 14 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial for the nRF52810

notsane0

Requirements This document uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52 DK to emulate the nRF52810 a BLE-enabled mobile device You may want to review the blog here for a more comprehensive…
- 8 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial

notsane0

Requirements This hands-on tutorial uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52840 DK a BLE-enabled mobile device You can use an nRF52 DK or nRF52833 DK instead of the nRF52840 DK,…
- 8 Apr 2022
Software: Building a Bluetooth application on nRF Connect SDK - Part 3 Optimizing the connection

Hung Bui

This is part 3 of the series Building a Bluetooth application on nRF Connect SDK You can find other parts here: Part 1 - Peripheral Role. Part 2 - Central Role. In Part 1 we covered the generic architecture…
- 21 Feb 2022
Peripherals And RF Test: Using Bluetooth Shell

Mark Q

Purpose The purpose of this guide is to demonstrate the use of Bluetooth Shell. Bluetooth Shell (BT Shell) is a command-line shell application that runs over the UART. It allows one to manually type in…
- 21 Jan 2022
Software: Memory Optimization with the nRF Connect SDK

matt.heins

Out of the box, the examples in the nRF Connect SDK are configured for ease of use, functionality, and debugging; they are not generally configured for optimal memory utilization. Some of the examples…
- 6 Jan 2022