Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Bricked my brand new nRF51-DK? 0

Hi, I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
- nrf51-dk
778 views

0 replies

Started over 10 years ago
by David
Not Answered

master slave, link 0

Hello, I would like to do an communication between Arduino and Android platform. In my case, Android will be master. But I want also test between 2 Arduino with an Bluetooth...

527 views

0 replies

Started over 10 years ago
by Vorms
Not Answered

How to write and read long characteristics in central S120? 0

I want to read and write long string in central side how it possible? Regards, Himansu

870 views

0 replies

Started over 10 years ago
by Himansu Donga
Not Answered
nRF8001 pairing with custom key or OOB 0

Hello, I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
- pairing
- nrf8001
- key
985 views

0 replies

Started over 10 years ago
by bgun
Not Answered
how to config the parameter of GZP_TX_RX_TRANS_DELAY? 0

i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now, is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
- nrf51822 nrf24lu1
637 views

0 replies

Started over 10 years ago
by herman

Recent in Nordic blog

Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015
An appeal to makers - why you should document your project, and how you can do it

Mahesh Venkitachalam

An appeal to makers - why you should document your project, and how you can do it. http://electronut.in/why-how-document-project/
- 3 Aug 2015

Latest guides

nRF5x: Current measurement guide: Introduction

Stian Røed Hafskjold

###Other relevant posts A concise guide to equipment setup, and how to use the development kit for current measurements can be found here: Measuring current with PCA10040 v0.9.0 A post that describes…
- 1 Dec 2015
nRF5x: General PCB design guidelines for nRF51 series

Petter Myhre

When designing a PCB with nRF51, nRF51822 or nRF51422, there are some rules that should be followed in order to get a good working radio/system, with a maximized range. General rule The RF part of the…
- 13 Nov 2015
Software Development Kit: nRF5 SDK Scheduler Tutorial

Einar Thorsrud

2019-02-08: Updated tutorial to cover nRF5 SDK version 15.2. Introduction Scope The following topics will be included in this tutorial: Configuration of the Scheduler library. Using the scheduler with…
- 9 Nov 2015
Bluetooth low energy: Bluetooth low energy central tutorial

Anders Strand

Scope Topics that will be covered include: Before we begin Necessary equipment and software Necessary prior knowledge Setting up the example projects Background theory Central and peripheral roles…
- 4 Nov 2015
Software Development Kit: nRF5 SDK Application Timer Tutorial

Einar Thorsrud

2018-11-23: Updated tutorial to cover SDK version 15.2. 2019-02-08: Improved example project (SDK 15.2) and updated instructions accordingly. Introduction Scope The following topics will be included in…
- 30 Oct 2015
Bluetooth low energy: Bluetooth low energy Services, a beginner's tutorial

MartinBL

Before we begin Scope Topics that will be covered include: Before we begin Necessary equipment and software Necessary prior knowledge Some basic theory The Generic Attribute Profile (GATT) Services…
- 26 Aug 2015