Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
gzp - runtime choice of either host or device mode 0

Hello. Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing: ...
- gzp
- gazell
800 views

0 replies

Started over 9 years ago
by ImQ009
Not Answered
nrf9E5 ADC Calibration 0

We would like to be able to calibrate the rRF9E5 ADC Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
- nrf9e5 adc calibration
655 views

0 replies

Started over 9 years ago
by Damien
Not Answered
breakpoints stopped working with nrf51-dk, gdb and JLinkGDBServer 0

At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger. At...
1403 views

0 replies

Started over 9 years ago
by Clem Taylor
Not Answered
Error: This has file has data in SoftDevice region 0

Hi, I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
- nrf51
- keil
- nrf51822
1572 views

0 replies

Started over 9 years ago
by Sarah
Not Answered
Read String from UART over BLE and execute function? 0

Hello I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
- nrf51-dk
- s110
- bluetooth low energy
- uart
- keil
- nrf51822
2366 views

0 replies

Started over 9 years ago
by kilianod

Recent in Nordic blog

Optimizing Power on nRF52 Designs

notsane0

As customers reach the end of their design cycle, their attention generally falls on power optimization, especially for battery powered designs. The following are hints for achieving the lowest possible…
- 30 May 2018
New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018

Latest guides

Software: Using nRF Connect SDK and west to compile and program the DTM example into the nRF52840 DK

Jay Tyzzer

Background There is a need to enable Nordic hardware with the Direct Test Mode (DTM) firmware. This is so the physical layer and RF characteristics may be ascertained as set in the Bluetooth Sig Specification…
- 14 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial for the nRF52810

notsane0

Requirements This document uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52 DK to emulate the nRF52810 a BLE-enabled mobile device You may want to review the blog here for a more comprehensive…
- 8 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial

notsane0

Requirements This hands-on tutorial uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52840 DK a BLE-enabled mobile device You can use an nRF52 DK or nRF52833 DK instead of the nRF52840 DK,…
- 8 Apr 2022
Software: Building a Bluetooth application on nRF Connect SDK - Part 3 Optimizing the connection

Hung Bui

This is part 3 of the series Building a Bluetooth application on nRF Connect SDK You can find other parts here: Part 1 - Peripheral Role. Part 2 - Central Role. In Part 1 we covered the generic architecture…
- 21 Feb 2022
Peripherals And RF Test: Using Bluetooth Shell

Mark Q

Purpose The purpose of this guide is to demonstrate the use of Bluetooth Shell. Bluetooth Shell (BT Shell) is a command-line shell application that runs over the UART. It allows one to manually type in…
- 21 Jan 2022
Software: Memory Optimization with the nRF Connect SDK

matt.heins

Out of the box, the examples in the nRF Connect SDK are configured for ease of use, functionality, and debugging; they are not generally configured for optimal memory utilization. Some of the examples…
- 6 Jan 2022